2,341 After very first print, extruder not heating up anymore ?
by jul654321
- 6 replies
- 3,843 views
- Last post 2012-11-02 22:10:20 by jul654321
2,342 print dies halfway through with "last line number error"
by JustSomeGuyTN
- 2 replies
- 2,085 views
- Last post 2012-11-02 13:45:59 by JustSomeGuyTN
2,343 Mis Aligned Axis
by utt.josh
- 7 replies
- 3,805 views
- Last post 2012-11-02 12:17:02 by utt.josh
2,344 Prints curling up
by elmoret
- 21 replies
- 17,686 views
- Last post 2012-11-01 21:25:06 by elmoret
2,345 Anyone have a brand of silicone lubricant to suggest
by JustSomeGuyTN
- 3 replies
- 3,190 views
- Last post 2012-11-01 19:46:33 by solijohn
2,346 Hot X-Axis motor
by Kvirre
- 6 replies
- 6,829 views
- Last post 2012-11-01 19:34:47 by solijohn
2,347 why does bed temp drop when using KISSlicer?
by JustSomeGuyTN
- 5 replies
- 6,239 views
- Last post 2012-11-01 19:33:42 by solijohn
2,348 damaged usb header
by Cwalster
- 9 replies
- 7,158 views
- Last post 2012-11-01 19:24:57 by solijohn
2,349 My two most annoying problems
by zimmer62
- 10 replies
- 7,743 views
- Last post 2012-10-26 21:56:46 by solijohn
2,350 Lessons learned
by ch355ma5t3r
- 10 replies
- 7,425 views
- Last post 2012-10-26 14:55:09 by solijohn
2,351 clogged extrusion tip?
by zimmer62
- 18 replies
- 19,106 views
- Last post 2012-10-26 14:50:21 by solijohn
2,352 Last ~4 layers are off
by surma
- 4 replies
- 2,870 views
- Last post 2012-10-24 16:33:04 by solijohn
2,353 Tighten up shaking parts
by Kvirre
- 13 replies
- 10,376 views
- Last post 2012-10-24 16:31:15 by solijohn
2,354 Melted Power Terminal
- 26 replies
- 25,865 views
- Last post 2012-10-24 16:30:19 by solijohn
2,355 Updating firmware fail
by creationblur
- 4 replies
- 2,727 views
- Last post 2012-10-24 16:27:02 by solijohn
2,356 Belt Tension and Screw Preloads
by jooshs
- 1 reply
- 2,144 views
- Last post 2012-10-19 13:23:44 by solijohn
2,357 Bed Screw holes leaving indents in flat prints
by kevin13
- 10 replies
- 8,089 views
- Last post 2012-10-17 21:35:29 by solijohn
2,358 Hot End Issues
by Caucasian
- 14 replies
- 10,379 views
- Last post 2012-10-17 21:35:03 by solijohn
2,359 Advice on repair
by gwoodlewistown
- 4 replies
- 3,107 views
- Last post 2012-10-17 21:33:05 by solijohn
2,360 Switching between ABS<>PLA
by Kvirre
- 3 replies
- 5,075 views
- Last post 2012-10-17 21:30:04 by solijohn
2,361 Filament doesn't stick
by surma
- 3 replies
- 5,016 views
- Last post 2012-10-12 14:40:44 by surma
2,362 printing solidoodle parts
by driggers
- 1 reply
- 2,048 views
- Last post 2012-10-07 19:12:37 by ch355ma5t3r
2,363 oh noes ! my extruder is having trouble moving
by lobosolo
- 1 reply
- 1,843 views
- Last post 2012-09-30 15:16:57 by lobosolo
2,364 Shutdown cleaning operations
by coleke
- 1 reply
- 2,190 views
- Last post 2012-09-27 18:15:00 by IanJohnson
2,365 can't home in the Y axis
by hoyle
- 4 replies
- 3,689 views
- Last post 2012-09-26 20:23:44 by zimmer62
2,366 What is causing this odd loops?
by AgentOrange
- 4 replies
- 3,478 views
- Last post 2012-09-13 05:40:33 by AgentOrange
2,367 Prints not sticking/Extruder skipping
by Caucasian
- 19 replies
- 16,672 views
- Last post 2012-09-02 16:47:11 by solijohn
2,368 Any tips on leveling the bed?
by zimmer62
- 14 replies
- 13,857 views
- Last post 2012-08-16 13:13:53 by Gordym