2,281 Odd noise at end of print
by perlguy
- 0 replies
- 989 views
- Last post 2012-12-26 16:47:25 by perlguy
2,282 Layer Adhesion
by perlguy
- 7 replies
- 5,352 views
- Last post 2012-12-26 13:08:56 by perlguy
2,283 Hot end dead? Please confirm...
by cmetzel
- 13 replies
- 6,153 views
- Last post 2012-12-23 15:45:26 by cmetzel
2,284 Z axis wobble
by jooshs
- 17 replies
- 12,471 views
- Last post 2012-12-23 05:59:17 by jefferysanders
2,285 Can't print for more than an hour
by jon_bondy
- 22 replies
- 12,964 views
- Last post 2012-12-22 18:13:25 by jon_bondy
2,286 No power to the unit
by mulion21
- 10 replies
- 6,805 views
- Last post 2012-12-21 14:22:56 by mulion21
2,287 Did anyone else get into power supply trouble ?
by jul654321
- 13 replies
- 13,531 views
- Last post 2012-12-21 14:21:27 by mulion21
2,288 Custom gcode
by DigitalWhitewater
- 2 replies
- 2,281 views
- Last post 2012-12-21 01:42:11 by Cwalster
2,289 i found out why the head was hitting, x cariage is cracked
by JustSomeGuyTN
- 7 replies
- 3,253 views
- Last post 2012-12-20 01:56:44 by Kyle Ward
2,290 Crashed Extruder
by Kyle Ward
- 2 replies
- 5,293 views
- Last post 2012-12-20 01:53:53 by Kyle Ward
2,291 Extruder Heater Failure at the Board
by jooshs
- 0 replies
- 1,257 views
- Last post 2012-12-20 01:37:49 by jooshs
2,292 Calibration Help
by perlguy
- 5 replies
- 3,539 views
- Last post 2012-12-19 02:51:13 by nickythegreek
2,293 Repetier Host Mac 0.51 Connecting Error
by GrilledPeaches
- 1 reply
- 1,720 views
- Last post 2012-12-18 01:22:46 by perlguy
2,294 Replacing the Z axis
by jooshs
- 2 replies
- 7,204 views
- Last post 2012-12-17 16:49:59 by jooshs
2,295 Extruder grinding filament and then skipping
by jamesh
- 8 replies
- 11,365 views
- Last post 2012-12-16 20:23:44 by HelmutK
2,296 nozzle hitting layer, anything i can do?
by JustSomeGuyTN
- 0 replies
- 3,265 views
- Last post 2012-12-15 02:57:08 by JustSomeGuyTN
2,297 White Powder Buildup - Right Y-Axis
by nickythegreek
- 7 replies
- 5,835 views
- Last post 2012-12-15 01:12:22 by nickythegreek
2,298 Error: Extruder switched off. MINTEMP triggered
by dkgr
- 4 replies
- 8,569 views
- Last post 2012-12-14 01:23:51 by dkgr
2,299 Solidoodle did stand by there product
by rov.design
- 0 replies
- 1,168 views
- Last post 2012-12-13 01:59:18 by rov.design
2,300 Help setting up printer after replacement of X carriage
by jon_bondy
- 9 replies
- 8,469 views
- Last post 2012-12-11 18:17:34 by jon_bondy
2,301 Wiring bundle interfering with belt and being torn by case
by jooshs
- 20 replies
- 17,141 views
- Last post 2012-12-11 17:24:36 by DePartedPrinter
2,302 Z-axis Stepper wobble
by cckens
- 11 replies
- 9,323 views
- Last post 2012-12-09 21:48:33 by rov.design
2,303 Wire Bundle Protective Sleeve
by jooshs
- 5 replies
- 6,374 views
- Last post 2012-12-09 12:52:33 by wire10ga
2,304 Hot end threaded tube dimensions
by wrward
- 2 replies
- 1,821 views
- Last post 2012-12-06 10:18:05 by wrward
2,305 where can i get ceramic paste for the extruder ?
by lobosolo
- 3 replies
- 2,425 views
- Last post 2012-12-06 09:38:24 by wrward
2,306 Bad prints go into the bin => how to recycle those ?
by 3D_CC_design
- 4 replies
- 2,611 views
- Last post 2012-12-05 20:15:46 by 3D_CC_design
2,307 Erratic movement on x-axis and not going into right direction
by shifter
- 6 replies
- 5,176 views
- Last post 2012-12-04 17:07:01 by shifter
2,308 Extruder is grinding filament into dust
by BotBot
- 7 replies
- 6,580 views
- Last post 2012-12-03 20:27:30 by HelmutK
2,309 Extruder skipping
by E_T
- 7 replies
- 7,539 views
- Last post 2012-12-03 14:36:24 by 3D_CC_design
2,310 Repetier connect issue
by aFoote
- 0 replies
- 1,231 views
- Last post 2012-12-03 10:27:20 by aFoote