961 Blobby Perimeters after E3D 0.6mm Install
by ne14pez
- 3 replies
- 1,548 views
- Last post 2014-06-02 02:22:39 by ne14pez
962 Problems with Y drive shaft alignment... need help
by CrazyBear
- 7 replies
- 3,826 views
- Last post 2014-06-02 01:49:01 by wardjr
963 Need Help with PLA threading
by mark.burhop
- 2 replies
- 1,618 views
- Last post 2014-05-31 15:30:35 by mark.burhop
964 Dial indicator question
by AZERATE
- 2 replies
- 1,558 views
- Last post 2014-05-31 14:58:37 by AZERATE
965 E3D v6 and MK5
by CrazyBear
- 4 replies
- 1,919 views
- Last post 2014-05-31 14:34:12 by wardjr
966 Firmware upload error ATMEGA644P
by driggers
- 0 replies
- 1,058 views
- Last post 2014-05-31 10:47:58 by driggers
967 Help! Help with Filament Extrusion
by WIsolidoodle
- 15 replies
- 7,900 views
- Last post 2014-05-30 20:44:09 by WIsolidoodle
- 0 replies
- 2,282 views
- Last post 2014-05-30 19:48:14 by mdrVB6
969 Double images
by Hoswvu
- 1 reply
- 678 views
- Last post 2014-05-30 17:56:25 by elmoret
970 The importance of PID autotune - BEGINNER REQUIRED READING
by FordGalaxie
- 5 replies
- 3,290 views
- Last post 2014-05-29 22:31:10 by wardjr
971 E3d and PID tuning
by TheOldMan
- 3 replies
- 3,228 views
- Last post 2014-05-29 17:38:34 by elmoret
972 Retraction settings
by paramite12
- 2 replies
- 1,398 views
- Last post 2014-05-29 12:15:49 by Damon550
973 Help! Clicking noise + Y-axis drift on brand new SD4
by devook
- 9 replies
- 7,274 views
- Last post 2014-05-29 11:53:01 by ysb
974 20 minutes to heat the bed SD2 glass
by driggers
- 15 replies
- 7,418 views
- Last post 2014-05-28 23:21:53 by paramite12
975 Printer not following coordinates
by ooberbanana
- 1 reply
- 790 views
- Last post 2014-05-28 11:54:11 by Serin
976 Can I use a Black Edition A4988 in the old Sanguinololu board (SD3)?
by CrazyBear
- 3 replies
- 1,617 views
- Last post 2014-05-27 22:32:39 by elmoret
977 Weird mid-layer extruder shift?
by mlove01001101
- 6 replies
- 2,304 views
- Last post 2014-05-27 15:24:51 by wardjr
978 Solidoodle 2 Led Strip
by patrickryan977
- 4 replies
- 2,632 views
- Last post 2014-05-27 00:15:12 by AZERATE
979 ABS & PLA on a E3D
by LdyMox
- 4 replies
- 1,731 views
- Last post 2014-05-24 18:35:21 by elmoret
980 Firmware update problem on Solidoodle 3
by jake
- 11 replies
- 7,099 views
- Last post 2014-05-23 20:28:59 by wardjr
981 Only ABS griding against the bed
by LdyMox
- 4 replies
- 1,837 views
- Last post 2014-05-23 16:26:17 by LdyMox
982 Tuning the bed's PID controllers
by mlove01001101
- 2 replies
- 1,449 views
- Last post 2014-05-23 13:41:31 by mlove01001101
983 Layer seperation
by rcav8r
- 3 replies
- 3,904 views
- Last post 2014-05-22 18:30:31 by rcav8r
984 Extruder doesn't stop when it hits the end of the x or y axis
by allegrovivo
- 15 replies
- 9,455 views
- Last post 2014-05-21 17:18:41 by bvaught
985 Pausing a print
by Ski52
- 1 reply
- 3,527 views
- Last post 2014-05-21 01:39:19 by grob
- 25 replies
- 16,616 views
- Last post 2014-05-20 13:44:32 by LdyMox
987 Help! Staggered Prints
by punxrus
- 2 replies
- 1,822 views
- Last post 2014-05-20 04:49:18 by ronsii
988 Da Vinci 1.0 Help
by ZillaFreak
- 1 reply
- 1,424 views
- Last post 2014-05-18 03:30:24 by ZillaFreak
989 Help! Fire Cement
by swiftimundo
- 4 replies
- 1,963 views
- Last post 2014-05-18 03:17:52 by swiftimundo
990 Solidoodle 4 possible calibration issue?
by Fuyuri
- 3 replies
- 1,696 views
- Last post 2014-05-17 03:49:45 by AZERATE