901 Individual Perimeters Not joining?
by FordGalaxie
- 5 replies
- 2,612 views
- Last post 2014-07-11 15:20:53 by mdrVB6
902 SD4: is a wobble normal?
by takadakeyo
- 3 replies
- 1,506 views
- Last post 2014-07-11 00:51:52 by takadakeyo
903 Speed settings for an E3D
by paramite12
- 2 replies
- 1,136 views
- Last post 2014-07-10 03:27:09 by wardjr
904 Checking voltages
by paramite12
- 6 replies
- 2,625 views
- Last post 2014-07-10 02:06:29 by grob
905 repetier refuses to keep my default extrusion temp
by paramite12
- 7 replies
- 4,378 views
- Last post 2014-07-10 02:04:44 by grob
906 Acetone question
by JammerX19
- 7 replies
- 3,513 views
- Last post 2014-07-09 04:13:49 by michael.t.albers
907 Why did my prints suddenly drop in quality so badly?
by mdrVB6
- 10 replies
- 4,777 views
- Last post 2014-07-08 02:42:33 by mdrVB6
908 'Bout had it with SD & iMac...
by Ski52
- 0 replies
- 948 views
- Last post 2014-07-08 00:38:21 by Ski52
909 Anyone else seeing this error downloading Repetier Host?
by mark.burhop
- 5 replies
- 2,770 views
- Last post 2014-07-07 08:19:30 by adrian
910 Install Solidoodle 2 via print server for mac
by luvdoraemon
- 5 replies
- 3,110 views
- Last post 2014-07-07 06:18:13 by grob
911 Help! Print stops abruptly with M999 error
by thegiantbark
- 2 replies
- 1,061 views
- Last post 2014-07-06 07:52:26 by bigbobby
912 What are the SD2 rod spacings?
by KD
- 1 reply
- 727 views
- Last post 2014-07-05 16:32:06 by KD
913 Level the bed with the wingnuts?
by JammerX19
- 1 reply
- 953 views
- Last post 2014-07-04 17:40:40 by IronMan
914 Help! Solidoodle 2 XYZ movements reversed
by aprzy15
- 1 reply
- 1,831 views
- Last post 2014-07-04 01:11:14 by Serin
915 Tweaking Tips Needed
by perlguy
- 9 replies
- 6,727 views
- Last post 2014-07-02 23:17:25 by IronMan
916 SD3 Y-Axis motor homing in wrong direction
by Lookitspants
- 7 replies
- 3,746 views
- Last post 2014-06-28 20:11:59 by Lookitspants
917 Help..Prints staggering
by pdarcy78
- 9 replies
- 5,459 views
- Last post 2014-06-28 05:21:13 by pdarcy78
918 Anyone else with lots of SD4 problems?
by hlaps1990
- 1 reply
- 1,293 views
- Last post 2014-06-28 00:28:46 by AZERATE
919 SD4 with Rumba only prints at back right corner
by hlaps1990
- 4 replies
- 2,257 views
- Last post 2014-06-27 04:18:24 by wardjr
920 SD4 Motherboard problem?
by hlaps1990
- 6 replies
- 3,038 views
- Last post 2014-06-26 16:41:41 by hlaps1990
921 SD2 not extruding at all
by robotscarecrow
- 22 replies
- 13,333 views
- Last post 2014-06-26 01:29:16 by elmoret
922 Help! How can print out a 3mm diameter hole?
by TonyLin
- 3 replies
- 3,018 views
- Last post 2014-06-23 23:35:07 by grob
923 Question on those who smooth
by LdyMox
- 5 replies
- 2,199 views
- Last post 2014-06-23 18:20:33 by IanJohnson
924 Help! Hello, i'm new, you can help me ?
by andysus
- 5 replies
- 2,053 views
- Last post 2014-06-21 07:21:23 by andysus
925 Solidoodle 4 help
by 7DSins
- 13 replies
- 7,300 views
- Last post 2014-06-20 19:05:09 by 7DSins
926 Random Slic3r Errors
by MolecularConcept
- 5 replies
- 4,906 views
- Last post 2014-06-20 16:59:04 by pirvan
927 Can I make my circles any better?
by aaronstalling
- 3 replies
- 1,223 views
- Last post 2014-06-20 15:45:45 by wardjr
928 Help! Abs prints coming out stringy and weak!!!???
by zipperboy
- 11 replies
- 8,795 views
- Last post 2014-06-20 03:29:20 by wardjr
929 Ramps 1.4 firmware installation
by Serin
- 3 replies
- 1,938 views
- Last post 2014-06-20 02:54:52 by wardjr
930 Change accelleration in Skeinforge
by TickTock
- 0 replies
- 640 views
- Last post 2014-06-19 23:48:31 by TickTock