931 Fluctuating temperatures in both bed and extruder
by zburhop
- 5 replies
- 2,519 views
- Last post 2014-06-19 13:03:48 by wardjr
932 Calibration issues Flow rate
by kalf
- 3 replies
- 1,956 views
- Last post 2014-06-18 21:18:00 by wardjr
933 SD3 set up!
by boyanzhelev
- 6 replies
- 2,821 views
- Last post 2014-06-18 21:11:07 by boyanzhelev
934 Help! Printing Error
by yamilbrunet
- 1 reply
- 813 views
- Last post 2014-06-18 18:12:20 by swiftimundo
935 Solved Supernight Wiring
by swiftimundo
- 4 replies
- 2,361 views
- Last post 2014-06-18 16:03:56 by wardjr
936 MK2 PCB Heater Firmware settings
by pirvan
- 1 reply
- 2,916 views
- Last post 2014-06-17 18:20:38 by pirvan
937 Printing poorly near holes in the wall
by d12dozr
- 3 replies
- 1,627 views
- Last post 2014-06-16 22:49:02 by DePartedPrinter
938 Heater Pad Dead... Again !
by pirvan
- 3 replies
- 1,649 views
- Last post 2014-06-16 12:52:56 by oklok
939 Solved Stupid question for a stupid move
by AZERATE
- 3 replies
- 1,599 views
- Last post 2014-06-15 00:54:22 by AZERATE
940 sd3 repetier "the port 'com3' does not exist"
by nemesis200
- 1 reply
- 1,664 views
- Last post 2014-06-14 18:38:11 by Randavian
941 Temperature is Reset error
by morty
- 14 replies
- 8,602 views
- Last post 2014-06-14 05:22:46 by j.bradley90
942 Parts printed are too small on Y axis
by Sim
- 5 replies
- 4,567 views
- Last post 2014-06-13 22:05:04 by Sim
943 Help! E3D v6 upgrade not heating
by adstaggs
- 3 replies
- 1,529 views
- Last post 2014-06-13 21:20:24 by adstaggs
944 Source for consistent quality 8mm rods
by mdrVB6
- 13 replies
- 7,707 views
- Last post 2014-06-13 13:33:21 by mdrVB6
945 Solidoodle Y-Axis shifting during printing
by mainelander
- 3 replies
- 1,792 views
- Last post 2014-06-13 11:56:46 by Gordym
946 Solved SD3 Power supply Upgrade
by clementscp
- 10 replies
- 5,531 views
- Last post 2014-06-12 18:51:37 by wardjr
947 Circle diameter vary by 0.3mm. Will the pillow block mod fix this?
by aaronstalling
- 6 replies
- 3,388 views
- Last post 2014-06-12 15:36:38 by wardjr
948 Top layer not quite filled (gaps)
by michael.genay
- 2 replies
- 2,170 views
- Last post 2014-06-12 15:23:27 by mdrVB6
949 Heat extruder not heating
by mgrude3
- 2 replies
- 957 views
- Last post 2014-06-10 05:33:55 by grob
950 E3D Heater block loosening
by Proteus
- 5 replies
- 3,258 views
- Last post 2014-06-09 19:06:23 by LdyMox
951 Solved Issues after multiple upgrades
by CrazyBear
- 3 replies
- 1,660 views
- Last post 2014-06-08 15:37:29 by CrazyBear
952 Help! Help! Filament not extruding while printing but does extrude manually!
by focal
- 3 replies
- 2,716 views
- Last post 2014-06-08 07:00:59 by aaronstalling
953Moved: help. is it okay if the plastic on thermocouple melts?
by chubbypanda
- No reply information
- No viewing information
- No last post information
954 Repetier - print stopping due to random resets
by mlove01001101
- 2 replies
- 1,325 views
- Last post 2014-06-05 14:20:02 by AZERATE
955 Y-Axis shifting mid print
by Proteus
- 3 replies
- 1,947 views
- Last post 2014-06-04 15:48:23 by mdrVB6
956 Can manually control SD3 but it won't print a model
by aaronstalling
- 1 reply
- 702 views
- Last post 2014-06-04 13:32:50 by Serin
957 Help! I think I fried my SD2 motherboard!
by mdrVB6
- 15 replies
- 8,134 views
- Last post 2014-06-03 18:34:22 by wardjr
958 Steps per millimeter
by CrazyBear
- 3 replies
- 2,554 views
- Last post 2014-06-02 20:53:16 by elmoret
959 Extruder stopped extruding smooth, now "steps"
by XistenZ
- 2 replies
- 1,077 views
- Last post 2014-06-02 11:07:23 by XistenZ
960 Help! why does this happen? please help
by iiinsaiii
- 8 replies
- 4,777 views
- Last post 2014-06-02 10:23:20 by iiinsaiii