1 Sticky: Bearings Don't Fit ABS Printed Parts
- 45 replies
- 31,007 views
- Last post 2016-11-02 17:33:23 by brucesdad13
2 Sticky: Print Troubleshooting guide
by Tin Falcon
- 6 replies
- 14,224 views
- Last post 2016-08-06 12:35:42 by hammade90
- 52 replies
- 106,446 views
- Last post 2015-05-05 15:32:35 by j1ceasar
- 41 replies
- 86,644 views
- Last post 2015-03-12 01:08:24 by hostinggeek
5 Help! Set Motor mode didnt get ack for message
by vaughnlogan2
- 3 replies
- 4,364 views
- Last post 2023-06-22 17:17:59 by escobar23w
6 Help! Solidoodle Press Ramps 1.4 Conversion
by robjac04
- 0 replies
- 496 views
- Last post 2023-05-29 01:26:26 by robjac04
7 Help! Need help setting up SD4 for the first time
by tortelli.victor
- 7 replies
- 5,713 views
- Last post 2021-09-04 13:38:18 by heartless
8 New to 3D printing
by ballard_88
- 4 replies
- 1,457 views
- Last post 2021-08-22 15:04:12 by Tin Falcon
9 Access to the port 'COM3' is denied
by Brutalsnowman
- 7 replies
- 120,587 views
- Last post 2021-08-22 14:52:43 by heartless
10 Need help getting SD2 up and running again
by wompus
- 4 replies
- 2,123 views
- Last post 2021-06-08 20:13:02 by justsomeguy
11 Solidoodle 2 bed sled needed
by capibara
- 5 replies
- 2,337 views
- Last post 2021-06-07 07:43:56 by wompus
12 I'm back! (Rebuilding my Solidoodle)
by TheBaron
- 16 replies
- 7,138 views
- Last post 2021-04-27 11:02:12 by knowack
- 7 replies
- 4,433 views
- Last post 2020-10-15 15:53:55 by Brutalsnowman
14 Filament bunching up between extruder gear and E3D V6
by kgkern01
- 4 replies
- 2,355 views
- Last post 2020-05-05 02:58:20 by kgkern01
15 Help! Replacing the Power Supply Pt. 2
by juliaragno
- 1 reply
- 1,192 views
- Last post 2020-04-14 22:00:36 by Tin Falcon
16 Help! Replacing the Power Supply
by juliaragno
- 2 replies
- 1,378 views
- Last post 2020-04-13 20:11:33 by juliaragno
17 Help! How to install a bootloader on a Sanguinololu 1.3a with 1284P in 2019+
by soliuser
- 3 replies
- 5,304 views
- Last post 2020-03-22 10:39:19 by soliuser
18 Help! Anet A8 won't print from SD card
by jfields115
- 1 reply
- 1,584 views
- Last post 2020-01-11 23:52:53 by carl_m1968
19 Broken 10mm rod clamp
by knowack
- 8 replies
- 3,287 views
- Last post 2019-11-22 04:52:55 by knowack
20 stuck @ 10 mm/s max printing speed
by Incognito24
- 11 replies
- 21,254 views
- Last post 2019-11-17 15:52:30 by heartless
21Moved: Filastruder Kit What Nozzle is 3.0mm that comes with the kit?
by Deadcatwalking
- No reply information
- No viewing information
- No last post information
22 Issue getting solidoodle 2 to connect to my pc through repetier
by hooliganskate
- 3 replies
- 2,011 views
- Last post 2019-10-14 01:18:01 by wardjr
23 Layer shifts.
by hammade90
- 4 replies
- 2,465 views
- Last post 2019-09-24 11:26:44 by heartless
- 26 replies
- 7,960 views
- Last post 2019-09-20 23:29:23 by Tin Falcon
25 Solved Extruder temp falls back to room temp at start
by TheBarnetts
- 23 replies
- 37,733 views
- Last post 2019-09-02 00:11:20 by LeinadDeraj2018
- 47 replies
- 13,520 views
- Last post 2019-08-28 00:43:48 by heartless
27 Need some help finding this part for my (new to me!) printer!
by evankardos5
- 2 replies
- 1,656 views
- Last post 2019-08-26 23:16:06 by heartless
28 Solidoodle not being detected
by Del
- 8 replies
- 3,286 views
- Last post 2019-08-04 14:50:30 by Tin Falcon
29 Help! SD3: Repetier connects but cannot move in x,y,z or heat extruder/plate
by bigoten13
- 0 replies
- 1,228 views
- Last post 2019-07-31 19:38:44 by bigoten13
30 Removing SD3 Z axis nut
by rsheldiii
- 4 replies
- 3,037 views
- Last post 2019-06-26 23:48:45 by heartless