1 Topic by jake

  • jake
  • Member
  • Offline
  • Registered: 2013-08-16
  • Posts: 28

Topic: Firmware update problem on Solidoodle 3

I need to update the firmware on my solidoodle3 printer to increase the maximum temperature for my new E3D hot-end. 

I have downloaded Arduino 1.0.5 and the firmware "solidoodle2-marlin-Marlin_v1".   I select the ATmega1284p 16MHz board, but when i upload i get the following error:

solidoodle2-marlin-Marlin_v1

I don't know if i have the incorrect firmware (i still have the default motherboard - rev. E) or if i have some incorrect settings.

2 Reply by 2n2r5 (edited by 2n2r5 2013-10-28 03:14:48)

  • 2n2r5
  • 2n2r5
  • Member
  • Offline
  • From: Frederick, MD
  • Registered: 2013-05-09
  • Posts: 1,208

Re: Firmware update problem on Solidoodle 3

Solidoodles Printrboard update guide http://wiki.solidoodle.com/update-firmware

Adrian's firmware http://www.soliforum.com/topic/4236/bet … ll-boards/

SD3 w/ mods:
Glass bed with QU-BD heat pad upgrade, threadless ballscrew w/ 8mm smooth rod, spectra line belt replacement, lawsy MK5 extruder, Lawsy replacement carriage, E3D hotend, Ramps 1.4 w/ reprap discount controller, DRV8825 drivers, 12v 30A PS, Acrylic case, Overkill Y-idlers, Filament alarm, Extruder fan + more.

2n2r5's Website

3 Reply by jake

  • jake
  • Member
  • Offline
  • Registered: 2013-08-16
  • Posts: 28

Re: Firmware update problem on Solidoodle 3

Thank you again 2n2r5!  Ill check that out this weekend.  smile

4 Reply by jake

  • jake
  • Member
  • Offline
  • Registered: 2013-08-16
  • Posts: 28

Re: Firmware update problem on Solidoodle 3

for answer, see: http://www.soliforum.com/topic/4520/e3d … 3-fw-help/

5 Reply by Bookmaker

  • Bookmaker
  • Member
  • Offline
  • Registered: 2013-11-04
  • Posts: 44

Re: Firmware update problem on Solidoodle 3

I have managed to get the file compiled and in my bootloader folder. I opened the case around the motherboard and found 3 sets of two boot pins.  Which ones do I jump?

6 Reply by ronsii

  • ronsii
  • Member
  • Offline
  • From: PNW
  • Registered: 2012-10-28
  • Posts: 1,723

Re: Firmware update problem on Solidoodle 3

Bookmaker wrote:

I have managed to get the file compiled and in my bootloader folder. I opened the case around the motherboard and found 3 sets of two boot pins.  Which ones do I jump?

So three different sets of pins have 'BOOT' printed next to them??? If so then you might have SD's newest controller board... I didn't know they switched already???

7 Reply by wardjr

  • wardjr
  • wardjr
  • Moderator
  • Offline
  • From: Minnesota
  • Registered: 2013-06-10
  • Posts: 5,624

Re: Firmware update problem on Solidoodle 3

This warrants a picture I'd be curious to know if they changed boards.

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

wardjr's Website

8 Reply by LdyMox (edited by LdyMox 2014-05-21 22:55:57)

  • LdyMox
  • LdyMox
  • Member
  • Offline
  • From: Buffalo, NY USA
  • Registered: 2013-04-27
  • Posts: 576

Re: Firmware update problem on Solidoodle 3

Which are the boot pins?

http://www.soliforum.com/misc.php?action=pun_attachment&item=5352&download=0

http://www.soliforum.com/misc.php?action=pun_attachment&item=5353&download=0

Post's attachments

20140521_183010.jpg
20140521_183010.jpg 3.74 mb, file has never been downloaded. 

20140521_183720.jpg
20140521_183720.jpg 2.7 mb, file has never been downloaded. 

You don't have the permssions to download the attachments of this post.
Tammy
Solidoodle 2
E3Dv6 Hotend, MK5 v6 version, Glass Bed, Anti Z backlash slop nut, SureStepr SD8825 1/32 Extruder Driver, makeshift breakaway plexiglass case; . L-Cheapo 3.8 Watt Laser Attachment w/Custom built enclosure
From Buffalo, NY, USA

9 Reply by LdyMox

  • LdyMox
  • LdyMox
  • Member
  • Offline
  • From: Buffalo, NY USA
  • Registered: 2013-04-27
  • Posts: 576

Re: Firmware update problem on Solidoodle 3

For an update, apprently this type of board you don't need to move any boot pins.

Tammy
Solidoodle 2
E3Dv6 Hotend, MK5 v6 version, Glass Bed, Anti Z backlash slop nut, SureStepr SD8825 1/32 Extruder Driver, makeshift breakaway plexiglass case; . L-Cheapo 3.8 Watt Laser Attachment w/Custom built enclosure
From Buffalo, NY, USA

10 Reply by Bookmaker

  • Bookmaker
  • Member
  • Offline
  • Registered: 2013-11-04
  • Posts: 44

Re: Firmware update problem on Solidoodle 3

http://i.imgur.com/5M8FuMh.jpg

11 Reply by AZERATE

  • AZERATE
  • AZERATE
  • PRINTiT
  • Offline
  • From: Chicago
  • Registered: 2013-11-28
  • Posts: 2,077

Re: Firmware update problem on Solidoodle 3

Just to clarify to future users with questions:

Bookmaker wrote:

http://i.imgur.com/5M8FuMh.jpg

This is a Printrboard Rev-E

ldymox wrote:

http://www.soliforum.com/misc.php?action=pun_attachment&item=5352&download=0

This is a Sang

The firmware update for these are a different process, so please take note smile

Printit Mason and Printit Horizon printers
Multiple SD2s- Bulldog XL, E3D v5/v6/Lite6, Volcano, Hobb Goblin, Titan, .9 motor, Lawsy carriages, direct Y drive, fishing line...the list goes on
Filawinder and Filastruder #1870.....worth every penny!

12 Reply by wardjr

  • wardjr
  • wardjr
  • Moderator
  • Offline
  • From: Minnesota
  • Registered: 2013-06-10
  • Posts: 5,624

Re: Firmware update problem on Solidoodle 3

Man, that's a nice looking Sang you should have a DRV8825 plugged into that thing for the extruder. wink

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

wardjr's Website