1,651 Sailfish Firmware
by pretenda
- 7 replies
- 4,695 views
- Last post 2012-10-24 16:12:53 by solijohn
1,652 Setup for Solidoodle 2
by rov.design
- 3 replies
- 4,354 views
- Last post 2012-10-24 15:37:37 by solijohn
1,653 Sanguino 12v power question for electronics gurus
by Diecrusher
- 5 replies
- 2,446 views
- Last post 2012-10-24 15:35:11 by solijohn
1,654 Repetier Host
by Kamatari
- 2 replies
- 2,650 views
- Last post 2012-10-24 15:28:52 by solijohn
1,655 Kickstarter Project Using the Solidoodle for Printing Parts
by jooshs
- 24 replies
- 12,481 views
- Last post 2012-10-24 15:24:23 by solijohn
1,656 Expert Model Case & Door
- 31 replies
- 18,016 views
- Last post 2012-10-24 15:17:48 by solijohn
1,657 hot air - will part melt?
by roger wall
- 6 replies
- 3,037 views
- Last post 2012-10-20 22:10:42 by roger wall
1,658 actual print mass
by roger wall
- 1 reply
- 1,180 views
- Last post 2012-10-20 12:00:01 by roger wall
1,659 What's it called
by cmetzel
- 8 replies
- 3,677 views
- Last post 2012-10-19 19:39:59 by solijohn
1,660 ABS fumes
by dubbsd
- 4 replies
- 2,700 views
- Last post 2012-10-19 14:52:50 by solijohn
1,661 Newbie: bedsize & other printing basics
by jjcuff1
- 15 replies
- 10,520 views
- Last post 2012-10-18 18:45:04 by ysb
1,662 "European-Orders" question
by Aldo
- 4 replies
- 2,750 views
- Last post 2012-10-18 14:32:00 by solijohn
1,663 Closed: August 17th Solidoodle Shipping Update
by Brad
- 4 replies
- 5,021 views
- Last post 2012-10-18 14:19:02 by solijohn
1,664 It's arrived... But...
by dbgw
- 24 replies
- 18,509 views
- Last post 2012-10-17 20:46:50 by solijohn
1,665 First impressions.
- 35 replies
- 21,048 views
- Last post 2012-10-17 20:12:24 by solijohn
1,666 Speeds in Slic3r
by Gordym
- 2 replies
- 2,457 views
- Last post 2012-10-17 20:10:11 by solijohn
1,667 How to IRC?
by coleke
- 4 replies
- 2,229 views
- Last post 2012-10-17 12:56:27 by solijohn
1,668Moved: Week 3 Solidoodle II Print Challenge (glider)
by lawsy
- No reply information
- No viewing information
- No last post information
1,669 Newbie Help
by XaroRSA
- 1 reply
- 1,428 views
- Last post 2012-10-14 15:09:40 by patmail4
1,670 Calibration required?
by t.servida
- 8 replies
- 5,685 views
- Last post 2012-10-13 15:01:29 by t.servida
1,671 Hmmm, would this work?
by cmetzel
- 7 replies
- 4,000 views
- Last post 2012-10-12 04:22:36 by cmetzel
1,672 Heated Bed?
by bpaylor2002
- 3 replies
- 2,205 views
- Last post 2012-10-11 11:27:05 by bpaylor2002
1,673Moved: Week 2 Solidoodle II Print Challenge (spinning top)
by lawsy
- No reply information
- No viewing information
- No last post information
1,674Moved: Week 1 Solidoodle II Print Challenge (double helix)
by jooshs
- No reply information
- No viewing information
- No last post information
1,675 Better MAC install how-to?
by Bad Coffee
- 1 reply
- 1,346 views
- Last post 2012-10-04 20:06:12 by Bad Coffee
1,676 Dedicated PC or not?
by Jinja
- 22 replies
- 14,870 views
- Last post 2012-10-03 18:20:31 by Brad
1,677 Another print question on speeding up a print
by JustSomeGuyTN
- 7 replies
- 4,490 views
- Last post 2012-10-03 18:02:17 by JustSomeGuyTN
1,678 Printing at .1mm, I'm getting some holes in the top of my prints
by JustSomeGuyTN
- 3 replies
- 3,039 views
- Last post 2012-10-03 15:57:15 by IanJohnson
1,679 Newbie Question: How to load filament in the middle of print
by andychan
- 2 replies
- 1,813 views
- Last post 2012-10-03 14:22:49 by andychan
1,680 OSX or Windows for Solidoodle Support Software..... Which is better?
by Diecrusher
- 2 replies
- 2,010 views
- Last post 2012-09-30 20:30:59 by Brad