- 11 replies
- 5,294 views
- Last post 2015-01-12 23:53:46 by pirvan
302 E3dv6 Z height changes SD4
by Annoying guest
- 4 replies
- 2,180 views
- Last post 2015-01-11 17:48:50 by Annoying guest
303 New filament guide for Solidoodle Workbench Apprentice
by Highender
- 12 replies
- 6,799 views
- Last post 2015-01-09 18:19:48 by IanJohnson
304 Filastruder Gummybears
by OneMoreCast
- 6 replies
- 3,830 views
- Last post 2015-01-09 14:47:16 by timp610
305 One problem with direct drive :-).
by Claghorn
- 3 replies
- 2,542 views
- Last post 2015-01-08 16:24:56 by wardjr
306 Trouble with my new e3d v6 on Solidoodle 4
by aecarver
- 20 replies
- 10,105 views
- Last post 2015-01-07 04:45:17 by grob
307 Heated bed temp, Many heavy mods
by lueman
- 0 replies
- 968 views
- Last post 2015-01-06 18:21:19 by lueman
- 29 replies
- 17,424 views
- Last post 2015-01-06 00:47:05 by n2ri
309 Need help wiring Rumba Board with SD3
by KWMarvel
- 3 replies
- 3,093 views
- Last post 2015-01-04 15:53:03 by mloebl
310 I did it, bowden extruder
by satman49
- 7 replies
- 4,283 views
- Last post 2015-01-01 20:26:33 by satman49
311 Squeak from the passive side front to back rod..
by jesseblnchrd
- 4 replies
- 2,661 views
- Last post 2014-12-30 23:45:55 by slimstar2
312 How to edit Firmware for e3d v6 thermistor on SD4
by nbourg8
- 4 replies
- 3,242 views
- Last post 2014-12-30 20:11:29 by nbourg8
313 Looking for a cheap tablet to run my solidoodle 2
by Jonathan
- 4 replies
- 2,815 views
- Last post 2014-12-28 22:36:07 by IanJohnson
314 Dual side fans, now with ducts
by accusedmonk
- 19 replies
- 16,808 views
- Last post 2014-12-27 16:46:40 by accusedmonk
315 Heat bed replacement MK2a
by MacGuyver20
- 8 replies
- 6,904 views
- Last post 2014-12-27 04:23:08 by satman49
316 E3D nozzles too big? [Edit: No!]
by TickTock
- 6 replies
- 3,729 views
- Last post 2014-12-24 17:08:13 by TickTock
- 16 replies
- 9,261 views
- Last post 2014-12-24 02:16:34 by jagowilson
318 loose lm8uu bearings
by satman49
- 7 replies
- 4,885 views
- Last post 2014-12-23 19:07:57 by wardjr
319 Misumi Packaging :-).
by Claghorn
- 8 replies
- 5,393 views
- Last post 2014-12-23 16:26:46 by Claghorn
320 The Turtle Moves!
by Claghorn
- 2 replies
- 1,486 views
- Last post 2014-12-22 12:36:58 by Claghorn
321 SD3 enclosure
by shields1.as
- 1 reply
- 1,269 views
- Last post 2014-12-20 03:30:02 by mdrVB6
322 Swap extruder and X-axis steppers?
by lawsy
- 5 replies
- 5,224 views
- Last post 2014-12-20 03:20:05 by RaceGeek
323 14:1 Geared Bowden Extruder
by accusedmonk
- 6 replies
- 6,259 views
- Last post 2014-12-19 20:00:32 by accusedmonk
324 A new extruder design
by kevin
- 2 replies
- 2,133 views
- Last post 2014-12-19 10:46:49 by kevin
325 new to solidoodle
by Timber2633
- 3 replies
- 2,099 views
- Last post 2014-12-19 04:34:48 by AOYOU3D
326 Best mods for solidoodle 4
by mccoyboy22
- 4 replies
- 2,313 views
- Last post 2014-12-19 04:29:37 by TickTock
327 Printing off a Raspberry Pi questions
by AZERATE
- 6 replies
- 3,724 views
- Last post 2014-12-16 04:59:19 by grob
- 28 replies
- 16,323 views
- Last post 2014-12-15 21:05:16 by blarz
329 Geared Y Drive Replacement
by pirvan
- 12 replies
- 6,702 views
- Last post 2014-12-14 03:19:46 by pirvan
330Moved: trying to understand bowden extruder
by satman49
- No reply information
- No viewing information
- No last post information