- 273 replies
- 222,044 views
- Last post 2019-03-26 10:33:10 by Damon550
- 84 replies
- 119,069 views
- Last post 2016-11-04 05:20:41 by brucesdad13
3 Sticky: How-To: Converting to a RAMPS Controller
- 65 replies
- 112,187 views
- Last post 2016-03-23 19:13:29 by fdm_process
- 162 replies
- 190,921 views
- Last post 2016-01-14 21:14:48 by mdrVB6
- 25 replies
- 38,988 views
- Last post 2015-09-17 04:45:51 by nzjonny5
- 66 replies
- 126,712 views
- Last post 2015-09-14 06:35:01 by metaldrgn
- 206 replies
- 232,505 views
- Last post 2015-07-06 13:00:07 by heartless
8 Sticky: Repetier for Solidoodle
- 71 replies
- 92,770 views
- Last post 2015-02-23 11:24:20 by Tin Falcon
- 100 replies
- 137,386 views
- Last post 2014-10-12 17:37:27 by jagowilson
- 73 replies
- 81,576 views
- Last post 2023-06-12 16:18:39 by justsomeguy
11 Re-use for Solidoodle Printer
by gckirk
- 1 reply
- 4,232 views
- Last post 2021-10-03 08:38:37 by Tin Falcon
12 Solidoodle 2 Titan/Aero conversion
by Claghorn
- 1 reply
- 1,225 views
- Last post 2021-09-25 07:05:51 by knowack
13 Ultrasonic mister for Acetone vapor post-processing?
by Retroplayer
- 7 replies
- 6,257 views
- Last post 2021-08-20 01:52:40 by IanJohnson
- 60 replies
- 42,699 views
- Last post 2021-06-07 06:17:53 by SirAlucard
15 Help! solidlab in process
by labotecno
- 1 reply
- 1,458 views
- Last post 2021-04-03 01:48:21 by Tin Falcon
- 34 replies
- 8,437 views
- Last post 2021-02-14 15:57:29 by heartless
17 Makerbot Replicator 2x revamp
by dineshwong
- 8 replies
- 7,557 views
- Last post 2021-01-23 19:14:02 by heartless
18 Replacement Solidoodle bed and upgraded leadscrew
by AZERATE
- 6 replies
- 4,480 views
- Last post 2020-12-20 17:03:26 by AZERATE
- 78 replies
- 49,116 views
- Last post 2020-12-16 20:59:52 by AZERATE v2
20 RAMPS 1.4 running on Solidoodle
by Rondavouz
- 13 replies
- 26,607 views
- Last post 2020-11-15 01:13:05 by lagunacomputer
21 Panelolu/ATmega1284 issue.
by Bad Coffee
- 10 replies
- 14,000 views
- Last post 2020-11-12 17:00:05 by jjhcs2
22 sos urgente
by javiercifuentes
- 0 replies
- 999 views
- Last post 2020-05-13 03:47:53 by javiercifuentes
23 Pancake Extruder Stepper?
by Brutalsnowman
- 3 replies
- 1,743 views
- Last post 2020-04-17 14:56:15 by Brutalsnowman
- 28 replies
- 10,170 views
- Last post 2020-03-25 23:10:10 by ESOCHI
- 77 replies
- 31,041 views
- Last post 2020-03-23 06:46:10 by badass_thumb
26 Help, extruder is not running
by debsinubg5
- 1 reply
- 1,099 views
- Last post 2020-03-20 20:57:10 by carl_m1968
- 25 replies
- 9,450 views
- Last post 2019-12-24 05:05:13 by knowack
28 SD4 with ballscrew for z-axis installed
by elenhinan
- 15 replies
- 10,575 views
- Last post 2019-07-26 11:33:24 by carl_m1968
29 Add A Filament Runout Sensor?
by Soapbox1858
- 4 replies
- 2,366 views
- Last post 2019-06-28 23:42:45 by heartless
30 Hobgoblin
by Ski52
- 4 replies
- 2,148 views
- Last post 2019-05-27 20:12:20 by Ski52