361 Removing the pressed in threaded rod (pics + guide)
by adrian
- 15 replies
- 17,127 views
- Last post 2014-11-16 18:45:32 by IronMan
362 Finally joined Thingiverse and posted.
by SnakeEyes
- 3 replies
- 1,788 views
- Last post 2014-11-15 22:57:06 by SnakeEyes
363 Want to replace hot end (e3d?)
by jsternbe
- 1 reply
- 1,672 views
- Last post 2014-11-15 18:21:36 by wardjr
364 updating SD2 Firmware on rev-e motherboard?
by mrniceguy119
- 2 replies
- 1,480 views
- Last post 2014-11-12 02:32:09 by mrniceguy119
365 Filament question.
by SnakeEyes
- 2 replies
- 1,745 views
- Last post 2014-11-11 00:08:20 by SnakeEyes
366 5 minute mod - <edit>*fewer*</edit> tangles
by TickTock
- 0 replies
- 1,596 views
- Last post 2014-11-10 01:32:43 by TickTock
- 32 replies
- 20,551 views
- Last post 2014-11-09 17:40:55 by Retroplayer
368 Finally went to bowden, amazing
by accusedmonk
- 18 replies
- 12,955 views
- Last post 2014-11-09 17:32:03 by accusedmonk
369 Need to run an idea through the gauntlet .... abs bed frame .......
by SnakeEyes
- 4 replies
- 2,312 views
- Last post 2014-11-08 19:51:16 by AZERATE
370 E3D v6 no PTFE tubing?
by mrniceguy119
- 8 replies
- 7,344 views
- Last post 2014-11-07 04:46:21 by elmoret
371 Using a Panelolu2 on a SD2 Printrboard
by theman00011
- 5 replies
- 4,132 views
- Last post 2014-11-06 21:43:13 by jabba400
372 PTFE Direct Feed Guide
by accusedmonk
- 1 reply
- 3,294 views
- Last post 2014-11-05 03:32:09 by n2ri
373 SD4 Dual Extruder Mod?
by trinium42
- 0 replies
- 1,024 views
- Last post 2014-11-05 00:59:55 by trinium42
374 SD2 E3D v6- thermocouple or thermomister?
by mrniceguy119
- 2 replies
- 2,562 views
- Last post 2014-11-04 15:55:31 by Ski52
375 Solidoodle apprentice mods/hacks
by brodbones
- 4 replies
- 2,427 views
- Last post 2014-10-31 16:50:53 by wardjr
376 Acceleration settings for upgraded solidoodles
by RaceGeek
- 0 replies
- 920 views
- Last post 2014-10-28 03:45:04 by RaceGeek
377 SD3 front of bed stabilizer
by Damon550
- 3 replies
- 1,967 views
- Last post 2014-10-27 19:48:53 by accusedmonk
378 Raspberry Pi and Octopi on SD4
by knowack
- 22 replies
- 16,840 views
- Last post 2014-10-24 17:10:50 by letroll
379 SD4 With a E3D V6 printing Temps
by trinium42
- 3 replies
- 2,392 views
- Last post 2014-10-24 11:48:29 by wire10ga
380 SD4 and E3D V6?
by Nerfz
- 12 replies
- 8,474 views
- Last post 2014-10-23 09:19:28 by trinium42
381 SD4 Mods?
by Zortwil
- 7 replies
- 4,893 views
- Last post 2014-10-22 02:38:16 by satman49
382 Step motor cooling
by hostage
- 2 replies
- 1,546 views
- Last post 2014-10-19 17:01:24 by Tin Falcon
383 Another Wiring Solution - Round Wire Conduit
by Krythis
- 4 replies
- 3,127 views
- Last post 2014-10-15 03:36:05 by Krythis
384 Printrboard upgrade
by zlagger
- 4 replies
- 2,553 views
- Last post 2014-09-29 20:06:15 by zlagger
385 E3D v6 Solidoodle 2 Bowden
by MacDoodle
- 17 replies
- 11,360 views
- Last post 2014-09-25 14:06:18 by mdrVB6
386 Bigger nut?
by Claghorn
- 10 replies
- 4,411 views
- Last post 2014-09-23 15:43:30 by KD
387 Replacement Z-Stepper Question
by PheonixSD3
- 2 replies
- 2,175 views
- Last post 2014-09-20 23:24:47 by PheonixSD3
388 Glass bed for Flashforge Dreamer
by memi205
- 0 replies
- 3,992 views
- Last post 2014-09-20 18:02:07 by memi205
- 3 replies
- 3,099 views
- Last post 2014-09-19 21:17:41 by tmclean
390 Rumba avr timeout error on upload
by DigitalWhitewater
- 6 replies
- 6,459 views
- Last post 2014-09-17 21:20:20 by DigitalWhitewater