61 Need Help with Build Plate Heating/Power issues
by megatron
- 4 replies
- 2,268 views
- Last post 2017-09-13 03:04:15 by william.fecke
62 A4988 current setting
by maaltan
- 0 replies
- 1,281 views
- Last post 2017-07-20 01:24:45 by maaltan
63 pcb to connect powerful laser
by Endurance_robots
- 0 replies
- 978 views
- Last post 2017-06-25 06:17:52 by Endurance_robots
64 Monoprice maker select thermistor problem
by chairsgotoschool
- 3 replies
- 2,420 views
- Last post 2017-06-10 18:52:31 by chairsgotoschool
65 E3D V6 on a CTC Dual
by carl_m1968
- 1 reply
- 1,474 views
- Last post 2017-04-26 01:52:38 by wardjr
66 X axis stopped working.
by diyengineer
- 13 replies
- 5,866 views
- Last post 2017-04-06 20:15:46 by IronMan
67 What kind of connectors does the solidoodle 3 use?
by paramite12
- 1 reply
- 1,115 views
- Last post 2017-03-27 16:39:34 by carl_m1968
68 ffc 20624 ribbon cable
by fargo87
- 0 replies
- 906 views
- Last post 2017-03-26 22:32:39 by fargo87
69 I try again to build an optimized nozzle
by Edwin
- 9 replies
- 4,153 views
- Last post 2017-03-25 14:40:07 by knowack
70 Raspberry pi to printer ratio
by diyengineer
- 2 replies
- 1,307 views
- Last post 2017-03-24 18:30:28 by JeremyLGSiegfried
71 Duet 0.8.5 review and guide
by Ggalisky
- 0 replies
- 1,960 views
- Last post 2017-03-23 17:09:27 by Ggalisky
72 how to add a extra stand alone power supply for the heated bed?
by hansen644
- 5 replies
- 2,876 views
- Last post 2017-03-18 01:30:20 by carl_m1968
73 e3dv6 nozzle clogging
by foul_owl
- 14 replies
- 8,080 views
- Last post 2017-03-07 00:26:27 by Tin Falcon
74 3 solidoodles in a cell
by diyengineer
- 17 replies
- 6,624 views
- Last post 2017-03-01 19:06:31 by diyengineer
75 Fan connectors on Geeetech
by ebarton97
- 5 replies
- 7,379 views
- Last post 2017-02-10 21:24:17 by tranzoo
76 Prusa i3 y stepper motor seized and buzzes
by greg_michigan
- 1 reply
- 1,736 views
- Last post 2017-01-19 11:37:17 by Tin Falcon
- 3 replies
- 22,521 views
- Last post 2017-01-15 04:37:09 by Anthem
- 12 replies
- 5,220 views
- Last post 2016-12-28 00:43:38 by Kronikabuse
79 I always run out of filament on long prints, any solutions?
by UP3DprintingChicka
- 4 replies
- 2,045 views
- Last post 2016-12-23 00:31:22 by Tin Falcon
80 Enclosure temperature control
by Isabella.K991
- 2 replies
- 2,574 views
- Last post 2016-11-22 06:59:34 by carl_m1968
81 Prints fine for 5 mins and then puffff
by poulan
- 12 replies
- 5,113 views
- Last post 2016-11-10 19:45:33 by poulan
82 Z stepper motor spat the dummy!
by gravy
- 6 replies
- 3,001 views
- Last post 2016-11-04 10:02:34 by Tin Falcon
83 PiBot Electronics
by carl_m1968
- 1 reply
- 1,719 views
- Last post 2016-10-29 12:09:02 by Tin Falcon
84 A New Gear for a Jeep Cherokee A/C motor
by Velly
- 0 replies
- 1,225 views
- Last post 2016-10-28 09:40:31 by Velly
85 Flashforge Finder vs Velleman Vertex K8400 printer.
by SophiaL
- 2 replies
- 2,093 views
- Last post 2016-10-24 22:40:36 by Tin Falcon
86 The importance of keeping a spare USB cable on hand...
by heartless
- 6 replies
- 3,784 views
- Last post 2016-10-24 21:54:23 by Tin Falcon
87 Control board ignores x axis limit switch
by NicoleJS
- 2 replies
- 1,717 views
- Last post 2016-10-12 21:38:24 by Kronikabuse
- 1 reply
- 1,333 views
- Last post 2016-09-25 22:30:44 by ME
89 All Metal Hot End
by wagnmkr
- 14 replies
- 6,342 views
- Last post 2016-09-14 17:26:49 by wagnmkr
90 Laser for Prusa
by pawan
- 2 replies
- 1,994 views
- Last post 2016-09-11 19:55:45 by Tin Falcon