841 Did SD change vanilla SD3 Support in RH?
by forrestmc4
- 3 replies
- 1,267 views
- Last post 2014-08-16 14:29:59 by wardjr
842 Jobs Taking Longer to Print
by my
- 8 replies
- 5,010 views
- Last post 2014-08-16 02:29:58 by my
843 Best Lubricant?
by Ggalisky
- 9 replies
- 5,775 views
- Last post 2014-08-15 21:42:45 by n2ri
844 Help! Stepper Motor causing beaded prints
by headstroon1992
- 23 replies
- 12,685 views
- Last post 2014-08-15 19:47:18 by mdrVB6
845 X stopped working after VREF tweak
by morty
- 16 replies
- 9,504 views
- Last post 2014-08-14 17:58:34 by wardjr
- 43 replies
- 21,660 views
- Last post 2014-08-14 01:35:42 by AZERATE
847 E3D Cold Extrusion Prevented
by AZERATE
- 6 replies
- 4,992 views
- Last post 2014-08-13 14:33:32 by wardjr
848 Help! Older drivers, newer board?
by FatalDischarge
- 7 replies
- 2,824 views
- Last post 2014-08-13 02:14:43 by wardjr
849 SD3 bed will not repond
by KWMarvel
- 4 replies
- 1,949 views
- Last post 2014-08-12 07:50:23 by grob
850 Solved filament stuck in the solidoodle machine
by simoneM
- 2 replies
- 1,175 views
- Last post 2014-08-12 04:53:34 by stuking2002
851 solidoodle 4 x axis movement problem
by airsoftwarrior345
- 12 replies
- 5,879 views
- Last post 2014-08-12 04:05:47 by airsoftwarrior345
852 Different thermistors
by Ggalisky
- 1 reply
- 1,071 views
- Last post 2014-08-08 04:05:14 by elmoret
853 Is it normal for my y axis pulley to move like this?
by aaronstalling
- 6 replies
- 2,904 views
- Last post 2014-08-07 08:55:33 by n2ri
854 No manual control except to home axis..........
by SnakeEyes
- 21 replies
- 11,127 views
- Last post 2014-08-07 02:05:34 by wardjr
855 Broken Extruder Wire?
by Zetto
- 1 reply
- 1,199 views
- Last post 2014-08-06 01:09:09 by Tomek
856 Filament is hitting the top of the enclosure Solidoodle 4
by DarrellS
- 5 replies
- 2,360 views
- Last post 2014-08-05 17:48:40 by DarrellS
857 Help! F*%king irregular circles
by aaronstalling
- 3 replies
- 2,033 views
- Last post 2014-08-04 23:24:16 by wardjr
858 Greasing the rods
by JammerX19
- 8 replies
- 4,156 views
- Last post 2014-08-04 07:33:16 by n2ri
859 ABS slurry ratio
- 28 replies
- 23,148 views
- Last post 2014-08-04 01:06:21 by adrian
860 Please review my test print
by DarrellS
- 10 replies
- 5,427 views
- Last post 2014-08-02 23:01:03 by exineport
861 Fried Terminal Block Connector - Elec Short
by Krythis
- 9 replies
- 5,167 views
- Last post 2014-08-02 22:48:08 by Krythis
862 PLA just LOVES to get jammed in the stock PEEK barrel. Any help?
by HestonKent
- 8 replies
- 4,757 views
- Last post 2014-08-02 03:57:10 by IanJohnson
863 Update Firmware or Buy a Better Motherboard?
by remmec
- 9 replies
- 6,124 views
- Last post 2014-08-01 23:26:30 by grob
864 Pillow block mod done. Circles still up to -0.5mm diameter deviation
by aaronstalling
- 2 replies
- 1,000 views
- Last post 2014-08-01 16:24:09 by aaronstalling
865 Help! Solid Infill not meeting Perimeter
- 40 replies
- 32,215 views
- Last post 2014-07-31 17:23:16 by valkoinen.rapu
866 Help me troubleshoot my print results
by fadi
- 3 replies
- 2,011 views
- Last post 2014-07-31 03:43:50 by grob
867 Help! Y-Axis Timing belt replacements
by Retroplayer
- 13 replies
- 6,409 views
- Last post 2014-07-31 00:50:23 by grob
868 Help with Pillow Block positioning
by aaronstalling
- 5 replies
- 2,206 views
- Last post 2014-07-30 03:26:50 by wardjr
869 Is there a visual guide to printing issues?
by DarrellS
- 2 replies
- 1,949 views
- Last post 2014-07-29 14:51:38 by DarrellS
870 A random nut just dropped unto my bed!
by XistenZ
- 6 replies
- 3,700 views
- Last post 2014-07-29 10:42:07 by XistenZ