691 multiple parts in xyzware
by bpanting75
- 2 replies
- 2,434 views
- Last post 2016-01-29 18:34:05 by bpanting75
692 1.0A does not work after cartridge reset
by Telemachus
- 22 replies
- 8,533 views
- Last post 2016-01-29 18:30:11 by mpoffo
693 25 x 25cm heatbed setup
by dusunenali
- 1 reply
- 1,069 views
- Last post 2016-01-29 17:53:40 by evanalmighty
694 Davinci Junior Spool Error
by KarlSap
- 2 replies
- 3,851 views
- Last post 2016-01-28 22:04:26 by mpoffo
- 9 replies
- 5,819 views
- Last post 2016-01-28 05:49:39 by deuse
696 Printer is printing off the bed
by tophie
- 9 replies
- 8,137 views
- Last post 2016-01-28 03:58:13 by carl_m1968
697 Tried to print, says "device not found"
by MrLego
- 6 replies
- 3,200 views
- Last post 2016-01-27 01:31:07 by wardjr
698 Da Vinci 1.0 PRO Unboxing & Impressions
by sfraden
- 17 replies
- 7,156 views
- Last post 2016-01-26 19:12:33 by sfraden
699 Best way to transport a da vinci jr safely?
by RelyingPizza
- 4 replies
- 1,967 views
- Last post 2016-01-26 18:36:16 by carl_m1968
700 print suggestions
by valguerra
- 4 replies
- 1,570 views
- Last post 2016-01-25 20:22:06 by 3Dex
701 "chuck chuck chuck" noise on extruder -DaVince 1.0 AIO
by josephehealy
- 3 replies
- 1,594 views
- Last post 2016-01-25 20:21:30 by mpoffo
702 Esun Cleaning filament and DaVinci 1.0 Pro.
by artanangus
- 0 replies
- 1,243 views
- Last post 2016-01-24 23:46:52 by artanangus
- 35 replies
- 16,061 views
- Last post 2016-01-24 02:45:40 by carl_m1968
704 Best way to remove a finished project from the print bed?
by RelyingPizza
- 7 replies
- 3,640 views
- Last post 2016-01-23 18:16:51 by carl_m1968
705 Davinci Duo HIPS getting stuck in nozzle
by kszwab
- 4 replies
- 2,118 views
- Last post 2016-01-23 06:51:04 by kszwab
706 kr-net
by valguerra
- 1 reply
- 1,012 views
- Last post 2016-01-22 03:23:50 by evanalmighty
707 Printing and scanning question
by valguerra
- 3 replies
- 1,423 views
- Last post 2016-01-21 20:29:58 by valguerra
708 Ruined my thermistor??
by Telemachus
- 4 replies
- 2,513 views
- Last post 2016-01-21 09:37:35 by scobo
709 Da Vinci AiO - Need help clearing a jam
by GeauxGhoti
- 7 replies
- 3,455 views
- Last post 2016-01-21 05:12:25 by josephehealy
710 Davinci Jr. Filament Stepper
by hydronaut
- 1 reply
- 1,389 views
- Last post 2016-01-21 02:03:49 by carl_m1968
- 0 replies
- 1,034 views
- Last post 2016-01-19 03:42:37 by reluttr
712 flash Da Vici 1.0
by Android272
- 6 replies
- 3,705 views
- Last post 2016-01-18 18:26:59 by mpoffo
713 Downgrade 2.0.1 firmware of DaVinci 1.0
by timoteojorge
- 2 replies
- 1,457 views
- Last post 2016-01-18 11:34:06 by timoteojorge
714 ABS/PLA repetier settings
by Farouq11
- 5 replies
- 3,813 views
- Last post 2016-01-18 00:12:02 by Farouq11
715 is 1.75mm flexible filament possible?
by robertf
- 7 replies
- 4,346 views
- Last post 2016-01-17 23:55:11 by robertf
716 Will a 1.0A carriage fit a 2.0A?
by deuse
- 4 replies
- 1,945 views
- Last post 2016-01-16 20:28:45 by deuse
717 Convert DAV 1.0 to Bowden ?
by knucklbustr
- 11 replies
- 5,635 views
- Last post 2016-01-16 20:05:16 by elmoret
718 Da Vinci AiO Extruder is not heating.
by Vinderex
- 2 replies
- 2,161 views
- Last post 2016-01-15 23:36:22 by mark.burton
719 filament not coming out
by jgapril
- 6 replies
- 3,284 views
- Last post 2016-01-15 23:00:47 by mark.burton
- 29 replies
- 24,164 views
- Last post 2016-01-15 12:00:13 by timoteojorge