661 Selling Da Vinci AIO
by raptor700yfz
- 0 replies
- 826 views
- Last post 2016-02-18 02:47:13 by raptor700yfz
662 What is considered a lot of hours for a 3D printer?
by raptor700yfz
- 2 replies
- 2,874 views
- Last post 2016-02-18 02:45:44 by Kronikabuse
663 Sporadic X axis shifting
by darkhawk
- 6 replies
- 4,483 views
- Last post 2016-02-18 01:09:34 by mark.burton
664 Da Vinci Jr Original SD Card Contents
by scotthay
- 1 reply
- 1,651 views
- Last post 2016-02-16 23:41:55 by jfkeller
665 Cleaning nozzles before printing , Da vinci 2.0 repetier 0.92
by immunity20
- 3 replies
- 2,226 views
- Last post 2016-02-16 20:37:29 by luc
666 3D printing accuracy - newbie questions
by immunity20
- 4 replies
- 2,264 views
- Last post 2016-02-15 22:49:13 by mark.burton
667 What has changed with new DaVinci 1.0A firmware 2.0.0?
by eositis
- 13 replies
- 9,012 views
- Last post 2016-02-15 16:03:24 by robertf
668 Wired E3D v6 jamming issue after printing PMMA filament
by DopeSkrit
- 3 replies
- 1,927 views
- Last post 2016-02-14 04:12:13 by tlc531
669 DaVinci 1.0 w/ Repetier Temperature Plot Issue
by mote.kyle
- 0 replies
- 1,082 views
- Last post 2016-02-13 21:16:05 by mote.kyle
670 Printing accuracy questions - newbie
by immunity20
- 2 replies
- 1,291 views
- Last post 2016-02-12 18:11:55 by scobo
671 Da Vinci 1.0 Pro
by kcjeepn
- 2 replies
- 1,682 views
- Last post 2016-02-10 19:26:57 by twwaters
672 No filament
by lubbinv
- 7 replies
- 2,769 views
- Last post 2016-02-10 08:26:48 by scobo
673 Cable harness connector
by parentemv
- 8 replies
- 2,994 views
- Last post 2016-02-09 02:17:48 by craigunderhill
674 ABS adhesion to PVA support Material
by m_ferrante
- 1 reply
- 1,421 views
- Last post 2016-02-08 23:07:51 by robertf
675 da vinci 2.0 repetier
by Chris732
- 5 replies
- 3,097 views
- Last post 2016-02-08 18:58:15 by kev0175
676 Extruder does not heat
by jquijado
- 4 replies
- 2,958 views
- Last post 2016-02-08 17:20:44 by gr8jedi
677 1.0A E3D & Bowden conversion mod
by evanalmighty
- 24 replies
- 17,675 views
- Last post 2016-02-06 09:31:18 by evanalmighty
678 !!Help!! Da Vinci 1.0A - Removing R29 Resistor for E3D V6
by BradR97
- 13 replies
- 7,085 views
- Last post 2016-02-06 08:37:56 by scobo
679 Help With Arduino Burning Up (Davinci to Ramps Conversion)
by dopesoner930
- 9 replies
- 4,371 views
- Last post 2016-02-05 23:31:33 by carl_m1968
680 Mod Podge--- Best adhesion yet!
by Telemachus
- 6 replies
- 5,847 views
- Last post 2016-02-05 18:29:15 by rv.mike
681 Ramps for davinci
by barry1685
- 5 replies
- 2,425 views
- Last post 2016-02-04 16:31:20 by rv.mike
682 Printing with no glue
by NoHands
- 16 replies
- 7,485 views
- Last post 2016-02-03 19:23:08 by carl_m1968
683 DaVinci 1.0A leadscrew pitch?
by dext0rb
- 3 replies
- 3,238 views
- Last post 2016-02-03 14:07:42 by chrismu
684 XYZWare for Pro (OSX 10.11) problem (OpenGl?)
by Esperanza
- 0 replies
- 1,893 views
- Last post 2016-02-02 16:49:37 by Esperanza
685 Breaking down a 1.0 (sales)
by RC1
- 4 replies
- 2,108 views
- Last post 2016-02-02 13:24:04 by RC1
686 bad scans da vinci 1.0AIO
by NoHands
- 6 replies
- 2,476 views
- Last post 2016-02-01 04:11:44 by NoHands
687 Da Vinci 1.0 AiO scan software not connected
by wookden2009
- 6 replies
- 8,355 views
- Last post 2016-01-31 07:49:27 by NoHands
688 bricked XYZ 1.0 during repetier upgrade...
by bheimiller
- 10 replies
- 6,608 views
- Last post 2016-01-31 05:47:39 by edwardsdakota51
689 Flashair III vs Octoprint
by Telemachus
- 11 replies
- 5,683 views
- Last post 2016-01-31 05:21:40 by mpoffo
- 32 replies
- 17,272 views
- Last post 2016-01-30 16:29:33 by deuse