241 Source for threaded rod and nuts?
by bfoz
- 13 replies
- 11,367 views
- Last post 2013-09-09 07:21:32 by robotdigg
242 How to increase your computer's swap file size for fewer (?) crashes
by Heartlander
- 0 replies
- 1,229 views
- Last post 2013-08-29 17:36:14 by Heartlander
243 Wire Gauge used on steppers.
by nlancaster
- 8 replies
- 6,462 views
- Last post 2013-08-23 14:27:57 by Tomek
244 Computer Systems to run large 3D structures
by str254
- 2 replies
- 1,635 views
- Last post 2013-08-21 17:13:29 by chuddly
245 replacement stepper motors
by chuddly
- 3 replies
- 2,540 views
- Last post 2013-08-18 23:30:44 by elmoret
- 32 replies
- 23,492 views
- Last post 2013-08-18 05:05:33 by Hazer
247 How to couple shaft (motor and auger)
by compoinci
- 0 replies
- 1,336 views
- Last post 2013-08-17 11:11:53 by compoinci
248 How much does it cost to build a room sized 3D printer?
by moyaanomalous
- 10 replies
- 7,330 views
- Last post 2013-08-17 04:30:26 by Tomek
249 E3D - ABS Print Temps
by Krythis
- 4 replies
- 13,226 views
- Last post 2013-08-07 19:25:28 by DePartedPrinter
250 New SD3 Printrboard Questions?
by remmec
- 12 replies
- 12,876 views
- Last post 2013-08-05 05:31:30 by Gomisan
251 FoldaRap.Please Help!
by jordanwatson223
- 3 replies
- 2,930 views
- Last post 2013-07-30 14:46:57 by jordanwatson223
252 Actual Cost Of Hot-end?
by Rocketman
- 3 replies
- 2,616 views
- Last post 2013-07-06 02:33:44 by adrian
253 Does anybody know where I could get another one of these?
by mlove01001101
- 2 replies
- 1,928 views
- Last post 2013-06-25 15:46:43 by mlove01001101
- 27 replies
- 17,859 views
- Last post 2013-06-24 15:33:36 by nlancaster
255 Is the motherboard also the power supply for the heater?
by mlove01001101
- 2 replies
- 2,081 views
- Last post 2013-06-19 14:30:56 by mlove01001101
256 Therminator 5 Hot end
by DigitalWhitewater
- 3 replies
- 2,414 views
- Last post 2013-06-19 07:13:39 by nlancaster
257 SD3 X axis limit switch
by satman49
- 4 replies
- 2,872 views
- Last post 2013-06-14 16:38:10 by adrian
258 Just purchased this power supply $7.50
by RavensCrest
- 0 replies
- 1,169 views
- Last post 2013-06-12 11:35:09 by RavensCrest
259 12v silicon headed bed
by digiprint
- 3 replies
- 2,025 views
- Last post 2013-06-09 23:17:37 by ronsii
260 Which is best place to pick up 12v supply for a cooling fan to board
by Staffordknot
- 5 replies
- 4,241 views
- Last post 2013-06-09 12:50:47 by Hunter Green
261 LCD Ramps in Sanguinololu
by phq1910
- 0 replies
- 1,568 views
- Last post 2013-06-07 16:42:26 by phq1910
262 Raspberry Pi not connecting?
by 3dgringo
- 5 replies
- 2,873 views
- Last post 2013-06-05 03:03:33 by 3dgringo
263 Setting up new steppers and drivers
by lawsy
- 13 replies
- 14,830 views
- Last post 2013-06-03 22:21:50 by elmoret
264 $21.50 360 Watt 12 VDC Power Supply
by 2n2r5
- 4 replies
- 2,602 views
- Last post 2013-05-25 05:33:47 by 2n2r5
265 No 12v from board
by pcpoirier
- 9 replies
- 5,788 views
- Last post 2013-05-18 22:31:07 by 2n2r5
266 original solidoodle nozzle ?
by ysb
- 1 reply
- 2,056 views
- Last post 2013-05-11 01:53:03 by Gordym
267 UDOO controller, possibilities....?
by DigitalWhitewater
- 1 reply
- 1,999 views
- Last post 2013-05-09 23:52:16 by adrian
268 current draw of stock SD3 extruder heatcore
by satman49
- 4 replies
- 3,115 views
- Last post 2013-04-12 18:32:46 by Leghk
269 Anyone know where else I can get these?
by JustSomeGuyTN
- 0 replies
- 1,630 views
- Last post 2013-04-12 17:20:14 by JustSomeGuyTN
270 Is there a problem with the USB port on the controller?
by Briggs
- 3 replies
- 2,336 views
- Last post 2013-04-11 19:02:20 by Zarni