391 Top surfaces rough
by Dispensergoeshere
- 0 replies
- 1,232 views
- Last post 2016-04-18 05:16:26 by Dispensergoeshere
392 X Axis Wire
by Rotisiv
- 0 replies
- 1,234 views
- Last post 2016-04-18 02:26:10 by Rotisiv
393 New Drive Gear Davinci Junior and Filament help
by HyruleJedi86
- 3 replies
- 8,571 views
- Last post 2016-04-14 15:03:00 by HyruleJedi86
394 Thin and weak walls
by mixmstr
- 5 replies
- 4,411 views
- Last post 2016-04-12 02:04:12 by reluttr
395 xyz jr help
by jltk87
- 4 replies
- 3,246 views
- Last post 2016-04-12 02:02:16 by reluttr
396 Need new Nozzels
by broy55
- 1 reply
- 1,618 views
- Last post 2016-04-06 19:53:31 by kauboy
397 brand new heater bed cracked again
by amaterov
- 7 replies
- 3,886 views
- Last post 2016-04-06 15:11:58 by kauboy
398 Sensor connector question
by Reloaded256
- 1 reply
- 1,492 views
- Last post 2016-04-04 17:49:07 by carl_m1968
399 Hardware Differences Between 1.0, 1.0A, AiO
by ne14pez
- 2 replies
- 2,070 views
- Last post 2016-04-04 15:42:47 by ne14pez
400 fixing stepper on davinci duo without frying the stepper control???
by tommy2toes
- 1 reply
- 1,447 views
- Last post 2016-04-03 03:00:32 by elmoret
- 0 replies
- 1,290 views
- Last post 2016-03-31 08:31:51 by iadbd100
402 Not working the way it should
by grahamengley
- 1 reply
- 1,369 views
- Last post 2016-03-30 21:52:21 by carl_m1968
403 message d'erreur 30
by smorta
- 0 replies
- 1,368 views
- Last post 2016-03-29 20:22:41 by smorta
404 Issues with circles, difference in spacing from pullies
by MrLego
- 2 replies
- 1,902 views
- Last post 2016-03-28 16:39:38 by viperz28
405 daVinci Pro 1.0 Filament Load Clicking
by wsurferdude
- 12 replies
- 7,469 views
- Last post 2016-03-26 17:52:08 by kauboy
406 XYZ da vinci 1.0A print bed problem, noise and slow speed
by Fhrisanfow
- 1 reply
- 1,459 views
- Last post 2016-03-24 12:10:31 by Fhrisanfow
407 printing PLA Davinci 2.0 A error
by darkAngle0591
- 1 reply
- 1,799 views
- Last post 2016-03-22 16:45:52 by tommy2toes
408 Is 25% waste of cartridge filament the norm?
by svon89
- 2 replies
- 2,464 views
- Last post 2016-03-17 22:59:08 by mark.burton
409 Thermistors reading wrong temps (Fried Main Board?)
by dschmidt54
- 4 replies
- 3,293 views
- Last post 2016-03-16 22:21:10 by mark.burton
410 Z banding (Da Vinci Jr 1.0w)
by jwalker55
- 1 reply
- 1,866 views
- Last post 2016-03-13 22:29:21 by zerzoumia
411 Just purchased a Da Vinci 1.0 pro and cant get wifi to work.
by Johnny-five
- 4 replies
- 5,955 views
- Last post 2016-03-09 20:30:48 by Johnny-five
412 Can't do long prints in the da vinci Junior
by rdlady
- 1 reply
- 1,876 views
- Last post 2016-03-09 19:25:07 by rdlady
413 132-S2M drive belt broke where to get replacements in Australia
by shakey230
- 7 replies
- 4,865 views
- Last post 2016-03-09 02:54:43 by wardjr
414 Top of model not printing correctly
by disasm
- 1 reply
- 1,458 views
- Last post 2016-03-08 18:11:31 by lwik
415 Silver Guide Tube Fitting Part #? for Junior?
by Rob68
- 8 replies
- 5,330 views
- Last post 2016-03-07 19:32:45 by rdlady
416 Help with failing prints
by chairsgotoschool
- 1 reply
- 1,451 views
- Last post 2016-03-03 10:39:32 by e.morgan93
417 Bottom layers a bit... off
by GeauxGhoti
- 1 reply
- 1,536 views
- Last post 2016-03-03 10:37:32 by e.morgan93
418 Aceton and ABS help secure my model
by lwik
- 4 replies
- 2,792 views
- Last post 2016-02-25 18:11:20 by BlankMan
419Moved: Solidoodle 3 Machine Failure at 225 C Extruder Temp
by crazyman2099
- No reply information
- No viewing information
- No last post information
420 20mm cube abs no pretty
by efes
- 3 replies
- 2,457 views
- Last post 2016-02-22 02:41:48 by carl_m1968