31 Liquidated Presses on eBay
by mrallinwonder
- 7 replies
- 3,700 views
- Last post 2017-03-23 15:23:12 by AOYOU3D
32 Re-Press
by trayracing
- 0 replies
- 1,119 views
- Last post 2017-03-13 03:25:52 by trayracing
33 Finally solved all my issues.
by seven2099
- 9 replies
- 5,430 views
- Last post 2017-02-02 06:41:32 by rrssll
34 solidoodle press board replacement information?
by firestartr33
- 10 replies
- 5,273 views
- Last post 2017-01-14 02:02:47 by TruFord93
35 Solidoodle press info
by Del
- 6 replies
- 4,471 views
- Last post 2017-01-14 01:53:15 by TruFord93
36 Fried my controller board, now what...
by cptskippy
- 2 replies
- 2,027 views
- Last post 2016-12-16 11:41:27 by Tin Falcon
37 Keep upgrading or replace it?
by rrssll
- 10 replies
- 5,272 views
- Last post 2016-12-16 04:44:37 by wardjr
38 Replacing nozzle
by trayracing
- 0 replies
- 1,091 views
- Last post 2016-11-16 01:41:54 by trayracing
39 pauses
by zburhop
- 6 replies
- 2,928 views
- Last post 2016-10-29 14:18:58 by trayracing
40 Extrusion Issues - Stripped Filament
by disrupterx
- 5 replies
- 3,468 views
- Last post 2016-09-03 16:48:29 by seven2099
41 Press Bed Leveling Issue
by 1985.camaro.350
- 13 replies
- 9,374 views
- Last post 2016-08-13 21:17:39 by seven2099
42 Help! Issue with z-home/z-offset calibration
by iDeNoh
- 5 replies
- 5,093 views
- Last post 2016-08-13 21:07:49 by seven2099
43 Back of the print bed higher than the front.
by luclin999
- 5 replies
- 3,717 views
- Last post 2016-08-13 21:07:13 by seven2099
44 Help! Solidoodle Press Manual
by xnex8080
- 0 replies
- 1,440 views
- Last post 2016-06-27 21:24:48 by xnex8080
45 Best Filament to use?
by luclin999
- 3 replies
- 2,310 views
- Last post 2016-06-19 11:41:47 by Tin Falcon
46 Issues with Extrusion...
by knightshade
- 6 replies
- 3,418 views
- Last post 2016-06-19 02:02:48 by trayracing
47 Extruder Stepper Motor Broken?
by neiledit
- 3 replies
- 3,005 views
- Last post 2016-06-16 20:24:22 by mrallinwonder
48 Taurino + RAMPS Firmware & auto level
by sdiglesias
- 0 replies
- 1,831 views
- Last post 2016-06-09 03:10:17 by sdiglesias
49 Wiring Stepper Motor
by willthewill
- 8 replies
- 4,082 views
- Last post 2016-05-25 08:21:37 by willthewill
50 Press Bed Heater
by ScRamjet
- 6 replies
- 2,976 views
- Last post 2016-05-19 00:00:43 by ScRamjet
51 Solidoodle Press X RUMBA board
by cedric.leclerc05
- 4 replies
- 2,802 views
- Last post 2016-05-11 14:00:05 by cedric.leclerc05
52 Motherboard died. Options?
by sdiglesias
- 1 reply
- 1,544 views
- Last post 2016-05-10 04:12:51 by wardjr
53 Filament not sticking
by rwb205
- 9 replies
- 4,374 views
- Last post 2016-05-08 16:34:25 by trayracing
54 Bed Heat Fix
by ScRamjet
- 4 replies
- 2,784 views
- Last post 2016-05-08 01:07:35 by trayracing
55 Help! Mounting MK3 heatbed to Press
by daphur
- 2 replies
- 1,765 views
- Last post 2016-05-06 03:48:15 by ScRamjet
56 Solidoodle is dead, where can I get spares.
by antonvanwouw
- 10 replies
- 5,433 views
- Last post 2016-04-25 23:34:41 by sandcub1971
57 Can't connect to Press after E3Dv6 upgrade
by cedric.leclerc05
- 3 replies
- 10,792 views
- Last post 2016-04-22 22:03:20 by ScRamjet
58 Printing , now not, Now Fixed again
by ScRamjet
- 2 replies
- 1,792 views
- Last post 2016-04-17 00:53:12 by ScRamjet
59 Printing Clear ABS
by ScRamjet
- 8 replies
- 4,468 views
- Last post 2016-04-16 21:23:07 by ScRamjet
60 Press and e3d titan
by trayracing
- 2 replies
- 1,616 views
- Last post 2016-04-15 07:48:15 by zburhop