691 newbie - solidoodle 3 , job does not start , (command waiting)
by osmanharac
- 4 replies
- 3,038 views
- Last post 2014-12-12 21:23:20 by osmanharac
692 Z QUIDE RODS
by satman49
- 5 replies
- 2,598 views
- Last post 2014-12-11 00:28:35 by grob
693 Overhang quality
by morty
- 9 replies
- 4,530 views
- Last post 2014-12-10 21:02:41 by morty
694 Determining printing issue & Metal Z carriage.
by Rocketman
- 1 reply
- 1,243 views
- Last post 2014-12-10 00:09:17 by wardjr
695 better cable management?
by Claghorn
- 12 replies
- 11,616 views
- Last post 2014-12-08 03:07:54 by elmoret
- 25 replies
- 15,568 views
- Last post 2014-12-07 05:18:31 by satman49
697 Fun with cylinders
by Claghorn
- 11 replies
- 5,354 views
- Last post 2014-12-04 02:04:12 by n2ri
698 Switched to Rambo, but nothing is moving
by ErroneousBosch
- 1 reply
- 12,141 views
- Last post 2014-12-03 03:31:21 by ErroneousBosch
699 help with flashing a board
by shields1.as
- 19 replies
- 8,963 views
- Last post 2014-12-02 21:14:50 by shields1.as
700 Bulldog XL can not handle flexibles
by Ggalisky
- 4 replies
- 2,210 views
- Last post 2014-12-02 15:15:14 by mdrVB6
701 Solidoodle 4 not printing on center
by imvirus16
- 4 replies
- 1,662 views
- Last post 2014-12-01 08:44:14 by redbarret
702 circle tolerances
by satman49
- 7 replies
- 5,131 views
- Last post 2014-11-30 20:17:57 by n2ri
703 Help! SD4 bottom surface twisting
by zohoplite
- 1 reply
- 779 views
- Last post 2014-11-30 02:06:21 by AZERATE
704 Flat sides when printing circles
by delorean175
- 1 reply
- 4,774 views
- Last post 2014-11-29 15:53:25 by wire10ga
705 SD4 problems
by pejo
- 20 replies
- 8,924 views
- Last post 2014-11-28 14:45:22 by wardjr
706 Why does solidoodle not just go to the e3d extruders?
by shields1.as
- 7 replies
- 2,965 views
- Last post 2014-11-27 16:18:43 by n2ri
707 SD4 Motherboard Replacement
by knowack
- 4 replies
- 2,072 views
- Last post 2014-11-26 03:42:48 by pirvan
708 Object does not show the same form after slicing
by imvirus16
- 3 replies
- 1,588 views
- Last post 2014-11-24 01:05:27 by n2ri
709 Controller stick extension not printing properly
by imvirus16
- 10 replies
- 4,891 views
- Last post 2014-11-23 20:07:35 by imvirus16
710 How to increase spiral vase speed in scli3r?
by Ggalisky
- 2 replies
- 1,791 views
- Last post 2014-11-23 16:51:12 by mdrVB6
711 Is my printer broken?
by zankrep
- 3 replies
- 1,959 views
- Last post 2014-11-22 13:52:07 by mbarr
712 Board bed heater burned up.
by accusedmonk
- 17 replies
- 8,664 views
- Last post 2014-11-21 00:41:53 by accusedmonk
713 Repetier host issues...........
by SnakeEyes
- 12 replies
- 6,265 views
- Last post 2014-11-20 20:26:02 by n2ri
714 Cant figure out connection issue
by Hoswvu
- 11 replies
- 4,312 views
- Last post 2014-11-20 19:56:39 by IronMan
715 Solidoodle 3 Problems
by Pooncakes
- 2 replies
- 1,055 views
- Last post 2014-11-20 15:02:00 by Hoswvu
716 had my nozzle clog in a bad way
by shields1
- 12 replies
- 6,308 views
- Last post 2014-11-20 14:09:01 by jagowilson
717 Help! Advice on Possible Nozzle Clog
by Boz
- 10 replies
- 86,768 views
- Last post 2014-11-18 14:49:26 by wardjr
718 Heated issues solidoodle 4 please help
by Wheelz501
- 2 replies
- 944 views
- Last post 2014-11-18 05:29:44 by Wheelz501
719 Help! OUter shells not touching
by roanlddunnjr
- 5 replies
- 3,079 views
- Last post 2014-11-18 05:01:34 by wardjr
720 Heater erratic, burnt pin, is this a dead board?
by dpotthast
- 6 replies
- 3,545 views
- Last post 2014-11-17 21:31:06 by Tomek