781 ABS slurry works excellent!
by shields1.as
- 1 reply
- 767 views
- Last post 2014-09-30 18:06:13 by cmetzel
782 ABS slurry works excellent!
by shields1.as
- 1 reply
- 743 views
- Last post 2014-09-30 18:06:04 by cmetzel
- 26 replies
- 17,086 views
- Last post 2014-09-30 01:16:06 by wardjr
- 1 reply
- 805 views
- Last post 2014-09-28 21:27:56 by wardjr
785 Fry's Electronics Shaxon PLA - Anyone use it?
by HestonKent
- 10 replies
- 7,261 views
- Last post 2014-09-28 04:20:37 by Felixusaprinters
786 X-axis issues
by cujo3131
- 2 replies
- 1,345 views
- Last post 2014-09-26 06:10:10 by watson45
787 Print Shifting - Need Advice
by Proteus
- 10 replies
- 4,979 views
- Last post 2014-09-24 21:02:19 by naimar
788 Updated Circle Calibration?
by Zortwil
- 7 replies
- 4,178 views
- Last post 2014-09-24 03:03:11 by wardjr
- 4 replies
- 2,655 views
- Last post 2014-09-23 04:42:15 by AOYOU3D
790 Help! Upgraded F/W, now I cannot move motors
by Abolfazl
- 0 replies
- 783 views
- Last post 2014-09-22 23:23:44 by Abolfazl
791 Where to buy New XYZ Chips?
by LdyMox
- 13 replies
- 15,321 views
- Last post 2014-09-20 15:19:09 by AZERATE
792 Printing problem
by hanlun.wong
- 4 replies
- 1,993 views
- Last post 2014-09-19 09:06:15 by hanlun.wong
793 code 10 error
by satman49
- 4 replies
- 2,015 views
- Last post 2014-09-19 05:45:35 by n2ri
794 Just got new SD4. Y Axis Help!
by Zortwil
- 3 replies
- 1,427 views
- Last post 2014-09-19 04:08:41 by grob
795 Solved Manual Control vs Axis Homing
by AZERATE
- 17 replies
- 8,389 views
- Last post 2014-09-16 21:21:53 by AZERATE
796 My First Print! Is that the best it can do?
by chrislondon
- 4 replies
- 2,309 views
- Last post 2014-09-16 18:46:10 by metaldrgn
797 Solved Replaced stock kapton tape
by metaldrgn
- 0 replies
- 751 views
- Last post 2014-09-16 16:34:49 by metaldrgn
798 Working out the bugs?
by twlum
- 4 replies
- 1,870 views
- Last post 2014-09-15 03:28:17 by AZERATE
799 Help! Bootloader
by slimstar2
- 0 replies
- 764 views
- Last post 2014-09-15 00:32:21 by slimstar2
800 Solved Erratic hot end temp
by metaldrgn
- 8 replies
- 5,808 views
- Last post 2014-09-14 22:00:19 by metaldrgn
801 PLA Filament Jamming
by Proteus
- 14 replies
- 7,242 views
- Last post 2014-09-14 21:16:16 by roli
802 SD3 extruder temp shuts off after starting print job.
by dinosaurcam
- 6 replies
- 2,993 views
- Last post 2014-09-11 04:40:04 by grob
803 Weird temperature errors on bootup despite no movement?
by ITman496
- 2 replies
- 1,240 views
- Last post 2014-09-09 22:59:00 by ITman496
804 still having problems with printer just stopping mid print
by shields1.as
- 20 replies
- 8,464 views
- Last post 2014-09-09 17:23:00 by shields1.as
805 Pro Tip for Kapton Users: 100 sheets for ~$20
by browner87
- 9 replies
- 4,911 views
- Last post 2014-09-09 11:59:08 by wire10ga
806 sd4 problems
by lsgraphics
- 6 replies
- 3,150 views
- Last post 2014-09-09 05:36:04 by lsgraphics
807 Just installed new E3D now no extruder or bed heat.
by Ski52
- 6 replies
- 2,505 views
- Last post 2014-09-08 10:38:28 by Ski52
808 Filament is irregular diameter?
by Claghorn
- 3 replies
- 1,699 views
- Last post 2014-09-08 04:25:51 by wardjr
809 I made a boo boo
by foofoodog
- 8 replies
- 4,312 views
- Last post 2014-09-08 02:39:50 by foofoodog
810 Z Axis Problems - Newbie Help Required!
by harris.wms
- 7 replies
- 2,989 views
- Last post 2014-09-08 01:14:58 by grob