391 Help! SoliPrint issues- Never Reach Temperature
by matag
- 1 reply
- 1,435 views
- Last post 2015-07-15 03:21:00 by grob
392 Help! CTC dual printer problems
by johnnycan1990
- 8 replies
- 6,509 views
- Last post 2015-07-14 17:37:48 by carl_m1968
393 New multimeter with thermocouple
by Claghorn
- 6 replies
- 3,748 views
- Last post 2015-07-14 05:06:28 by grob
394 Tore off the 12 volt screw connector from the electronics board
by Skyler101
- 3 replies
- 2,298 views
- Last post 2015-07-13 05:46:40 by Skyler101
395 Help find a replacement extruder motor: 400 steps/rev
by jeffreuter
- 1 reply
- 1,279 views
- Last post 2015-07-12 21:03:31 by Tin Falcon
396 Feed Wheel eating filament
by patrick.w.york
- 5 replies
- 36,726 views
- Last post 2015-07-10 15:26:52 by wardjr
397 Help! My printer stopped all of sadden during the print
by michal85d
- 0 replies
- 962 views
- Last post 2015-07-10 08:23:03 by michal85d
398 Help! hot end and bed wont heat up
by tonyhughes
- 6 replies
- 3,193 views
- Last post 2015-07-09 13:40:44 by tonyhughes
399 Centering prints in Repetier
by chancrescolex
- 12 replies
- 9,007 views
- Last post 2015-07-08 23:47:08 by chancrescolex
400 Help! Printed Bed to high
by Mahkz
- 4 replies
- 2,126 views
- Last post 2015-07-08 20:39:45 by Mahkz
401 Prints not sticking on the extremities
by calishark21
- 7 replies
- 3,341 views
- Last post 2015-07-04 14:29:19 by TickTock
402 Help! E3D hot end, all printing fails
by damas_j
- 1 reply
- 1,243 views
- Last post 2015-07-03 12:08:51 by Quintox303
403 How do I make my lines really close?
by calishark21
- 3 replies
- 2,072 views
- Last post 2015-07-02 19:28:47 by TheBaron
404 Help! E3D hot end, all printing fails
by damas_j
- 3 replies
- 2,185 views
- Last post 2015-06-29 20:17:47 by AZERATE
405 Clumpy infill? (Humid filament) How do you fix it/store it?
by jwmflying14
- 5 replies
- 4,875 views
- Last post 2015-06-29 13:04:03 by heartless
406 Repair Shops
by Danthefisherman
- 1 reply
- 1,050 views
- Last post 2015-06-26 07:52:15 by carl_m1968
407 Using Sli3er for multiple items. Latest version.
by Rocketman
- 0 replies
- 1,003 views
- Last post 2015-06-24 19:58:58 by Rocketman
408 Large print failed half way through... TWICE
by chancrescolex
- 0 replies
- 7,426 views
- Last post 2015-06-21 07:00:56 by chancrescolex
409 printer head tool snapped off in nozzle
by Danthefisherman
- 2 replies
- 1,515 views
- Last post 2015-06-20 08:08:34 by Danthefisherman
- 36 replies
- 16,169 views
- Last post 2015-06-20 04:37:02 by Rocketman
411 Using brims in Repetier
by Rocketman
- 22 replies
- 15,867 views
- Last post 2015-06-19 14:35:13 by wardjr
412 Ramps 1.4 Setup with RH
by BFresh
- 11 replies
- 8,328 views
- Last post 2015-06-19 12:02:22 by BFresh
413 New issue... Need some insight
by cujo3131
- 12 replies
- 5,598 views
- Last post 2015-06-18 04:14:46 by grob
414 New e3d, but thermistor only reading about half temperature
by snowcapjr
- 8 replies
- 3,672 views
- Last post 2015-06-17 23:48:06 by grob
415 Filament constantly spills over the side of the reel and ruins prints
by chancrescolex
- 9 replies
- 9,722 views
- Last post 2015-06-15 13:30:45 by heartless
416 (SD4) Drive Gear problems and more?
by takadakeyo
- 14 replies
- 6,919 views
- Last post 2015-06-14 01:09:38 by Tin Falcon
417 Spool unwinding
by eflyguy
- 16 replies
- 13,078 views
- Last post 2015-06-12 17:56:51 by pirvan
418 original solidoodle 3 extruder
by Manx
- 3 replies
- 1,808 views
- Last post 2015-06-12 14:55:32 by wardjr
419 Solidoodle Press 3rd party support in NYC
by celboy
- 2 replies
- 1,298 views
- Last post 2015-06-10 21:05:18 by shathaway
420 Extruder cooling fan for stock extruder. Solidoodle 3.
by osmanharac
- 0 replies
- 946 views
- Last post 2015-06-10 21:00:07 by osmanharac