Re: Carriage going to lower left corner after print??
I'm attaching an abridged G-Code. Let me know what you think?
26 2015-06-14 17:50:57 (edited by Rocketman 2015-06-14 17:51:32)
- carl_m1968
- Member
- Offline
Re: Carriage going to lower left corner after print??
Based on the Gcode this is the final move,
G1 X56.959 Y83.821 E2.95972
Now the question is is this line of code the same in all your prints and if so where is it being generated?
Printing since 2009 and still love it!
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.
Re: Carriage going to lower left corner after print??
carl_m1968 wrote:
Based on the Gcode this is the final move,
G1 X56.959 Y83.821 E2.95972
Now the question is is this line of code the same in all your prints and if so where is it being generated?
I don't know if all my prints produce this code but I will check. How do I determine how it ends up in the gcode?
- carl_m1968
- Member
- Offline
Re: Carriage going to lower left corner after print??
Rocketman wrote:
carl_m1968 wrote:Based on the Gcode this is the final move,
G1 X56.959 Y83.821 E2.95972
Now the question is is this line of code the same in all your prints and if so where is it being generated?
I don't know if all my prints produce this code but I will check. How do I determine how it ends up in the gcode?
You need to look through all your slicer settings and host settings and see if there are any coordinates set anywhere that are similar or match these. It could be in your end gcode, or it may be an actual host setting that is getting exported to the slicer.
Printing since 2009 and still love it!
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.
Re: Carriage going to lower left corner after print??
I've had two different SD techs go through my settings and also reinstalled my Repetier software. What could they have missed?
- heartless
- Member
- Offline
Re: Carriage going to lower left corner after print??
honestly, I dont havwe a lot of faith in SD techs... hate to say that, but there it is...
These are my settings in RH, under Config > Printer settings...
Printer tab:
Printer Shape tab:
My settings in Slic3er Configuration > Printer Settings tab > General:
and Slic3r Configuration > Printer Settings tab > Custom G-code
I don't have a lot of custom g-code because I don't leave my printer unattended, heating is done/monitored manually.
SD4 #1 & #2 - Lawsy carriages, E3D v6, Rumba controller board, mirror bed plate, X motor fan, upgraded PSU & Mica bed heater
SD4 #3 - in the works ~ Folgertech FT-5, rev 1
Printit Industries Beta Tester - Horizon H1
SD4 #3 - in the works ~ Folgertech FT-5, rev 1
Printit Industries Beta Tester - Horizon H1
Re: Carriage going to lower left corner after print??
I just checked your settings against mine. They seem to be the same except for some temperature settings and print space respectively. Park position is 159, 150, and 50 respectively.
Start and End code is empty in sli3er settings, but there is Start and End Code in GCode Editor. Just:
Start Code
G21; set mm units
G90; set absolute coordinates
G92 E0; reset extruder distance
G28 X0 Y0;home x and y axis
G1 X75 Y75 F4000; move Nozzle above bed
G28 Z0; home Z axis
G92 E0; reset extrusion distance
End Code & Kill Code
G28 X159 Y150
G91
G1 Z50 F50
G90
I am thinking anything that says X0 Y0 should be removed if Park and Home positions are the same. Correct?
- carl_m1968
- Member
- Offline
Re: Carriage going to lower left corner after print??
Rocketman wrote:
I just checked your settings against mine. They seem to be the same except for some temperature settings and print space respectively. Park position is 159, 150, and 50 respectively.
Start and End code is empty in sli3er settings, but there is Start and End Code in GCode Editor. Just:
Start Code
G21; set mm units
G90; set absolute coordinates
G92 E0; reset extruder distance
G28 X0 Y0;home x and y axis
G1 X75 Y75 F4000; move Nozzle above bed
G28 Z0; home Z axis
G92 E0; reset extrusion distanceEnd Code & Kill Code
G28 X159 Y150
G91
G1 Z50 F50
G90I am thinking anything that says X0 Y0 should be removed if Park and Home positions are the same. Correct?
That would seem logical since X0 Y0 would be the opposite of X159 Y150.
Printing since 2009 and still love it!
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.
34 2015-06-18 14:06:11 (edited by heartless 2015-06-18 14:09:49)
- heartless
- Member
- Offline
Re: Carriage going to lower left corner after print??
Rocketman wrote:
I just checked your settings against mine. They seem to be the same except for some temperature settings and print space respectively. Park position is 159, 150, and 50 respectively.
Start and End code is empty in sli3er settings, but there is Start and End Code in GCode Editor. Just:
Start Code
G21; set mm units
G90; set absolute coordinates
G92 E0; reset extruder distance
G28 X0 Y0;home x and y axis does the printer "home" correctly when starting a print?
G1 X75 Y75 F4000; move Nozzle above bed
G28 Z0; home Z axis
G92 E0; reset extrusion distanceEnd Code & Kill Code
G28 X159 Y150
G91
G1 Z50 F50
G90I am thinking anything that says X0 Y0 should be removed if Park and Home positions are the same. Correct?
the only thing I can suggest is to remove the coordinates completely from the end/kill code so it reads: G28 X Y
SD4 #1 & #2 - Lawsy carriages, E3D v6, Rumba controller board, mirror bed plate, X motor fan, upgraded PSU & Mica bed heater
SD4 #3 - in the works ~ Folgertech FT-5, rev 1
Printit Industries Beta Tester - Horizon H1
SD4 #3 - in the works ~ Folgertech FT-5, rev 1
Printit Industries Beta Tester - Horizon H1
35 2015-06-19 01:08:05 (edited by Rocketman 2015-06-19 01:09:25)
Re: Carriage going to lower left corner after print??
In both the end and kill code in gcode editor I changed the x 159 y 150 to 100 for both. At end of print it retreated in the same direction but stopped a little beyond the middle of the print space. Apparently different parts of Repetier use reversed coordinates. What I defined as park position as 159x150 didn't matter. Gcode editor defines home as 0,0 while printing coordinates and home definition reverses it, it would seem.
- heartless
- Member
- Offline
Re: Carriage going to lower left corner after print??
hmmm... just for grins, try setting the positions to 50 for both and see what happens? where does it stop?
It may be that something in the firmware is different for yours vs mine...
SD4 #1 & #2 - Lawsy carriages, E3D v6, Rumba controller board, mirror bed plate, X motor fan, upgraded PSU & Mica bed heater
SD4 #3 - in the works ~ Folgertech FT-5, rev 1
Printit Industries Beta Tester - Horizon H1
SD4 #3 - in the works ~ Folgertech FT-5, rev 1
Printit Industries Beta Tester - Horizon H1
Re: Carriage going to lower left corner after print??
heartless wrote:
hmmm... just for grins, try setting the positions to 50 for both and see what happens? where does it stop?
It may be that something in the firmware is different for yours vs mine...
I think I've done enough experimenting for a while. lol. I just need to learn how to make that change permanent.