181 Help! sd2 in need of upgrade!!!
- 47 replies
- 21,094 views
- Last post 2016-03-16 18:15:10 by Jonathan
182 (SD4)Very messy prints... Possibly my settings?
by takadakeyo
- 23 replies
- 11,536 views
- Last post 2016-03-16 01:25:52 by AZERATE
183 Help! Connector for Heated Bed
by knewsom
- 5 replies
- 3,005 views
- Last post 2016-03-13 03:02:52 by wardjr
184 X motor not moving? Bad motor? (vid)
by takadakeyo
- 19 replies
- 9,550 views
- Last post 2016-03-09 01:09:16 by takadakeyo
185 pla sticking problem
by maaltan
- 13 replies
- 7,420 views
- Last post 2016-03-08 02:36:27 by AOYOU3D
186 solidoodle 2 extruder upgrade
by maaltan
- 23 replies
- 12,606 views
- Last post 2016-03-07 21:16:49 by protorix
187 looking for the driver for windows 10 for solidoodle 2
by williegfatboy
- 2 replies
- 16,056 views
- Last post 2016-03-05 07:58:37 by Ski52
188 Looking for Repetier Host for Workbench Apprentice
by Bruteforce123
- 14 replies
- 7,541 views
- Last post 2016-03-04 18:01:53 by n2ri
189 Kapton adhesive failure.
by maaltan
- 8 replies
- 4,754 views
- Last post 2016-03-04 15:46:12 by maaltan
190 SD4 X motor pulley grub screw removal?
by takadakeyo
- 5 replies
- 3,087 views
- Last post 2016-03-04 03:01:26 by takadakeyo
191 911, my Solidoodle is in a hermetically induced coma!
by Heartlander
- 5 replies
- 3,166 views
- Last post 2016-03-02 17:31:55 by Heartlander
192 Solidoodle 3 Machine Failure at 225 C Extruder Temp
by crazyman2099
- 10 replies
- 6,481 views
- Last post 2016-02-29 03:02:10 by wardjr
- 17 replies
- 8,512 views
- Last post 2016-02-27 17:57:40 by heartless
194 Which tape to use to stick back on my bed heater and insulation
by rantinan
- 2 replies
- 1,600 views
- Last post 2016-02-26 06:28:53 by rantinan
195 Solidoodle 2: Connection's Disappeared / Can't Reconnect
by TeleBlaster
- 11 replies
- 5,579 views
- Last post 2016-02-24 00:47:45 by n2ri
196 Help! Solidoodle Workbench randomly pausing, extruding then retracting.
by RaymondSheh
- 7 replies
- 5,623 views
- Last post 2016-02-23 14:04:23 by heartless
197 error code 0033
by technician911
- 5 replies
- 6,284 views
- Last post 2016-02-21 23:19:03 by Eoster1971
198 Solved Extruder pulse moire at 1/32 microstepping causing diagonal lines?
by PheonixSD3
- 11 replies
- 26,713 views
- Last post 2016-02-21 00:28:05 by lukie80
199 Bed Settings
by FatGremlin
- 4 replies
- 2,466 views
- Last post 2016-02-20 04:32:39 by carl_m1968
200 Two new printers with buzzing Y axies
by russcox
- 5 replies
- 2,954 views
- Last post 2016-02-19 19:22:24 by russcox
201 E3dv6 temp is fluctuating.... then won't raise above 213.
by clydehargis
- 2 replies
- 1,510 views
- Last post 2016-02-18 12:26:08 by heartless
202 Help! sloppy prints with the WorkBench
by CSwan
- 2 replies
- 1,567 views
- Last post 2016-02-17 23:17:25 by userksh14
203 E3D, Printrboard & moire...
by heartless
- 8 replies
- 13,249 views
- Last post 2016-02-17 13:00:05 by heartless
204 Z Axis stop switch thumb wheel bracket
by dave.lantz
- 1 reply
- 1,084 views
- Last post 2016-02-15 16:25:37 by dave.lantz
205 (S4) Setting beginning project movement order?
by takadakeyo
- 5 replies
- 2,843 views
- Last post 2016-02-15 03:29:27 by AZERATE
- 37 replies
- 16,393 views
- Last post 2016-02-15 02:53:23 by AZERATE
207 Mystical layer shifting?!
by JesperJuul
- 6 replies
- 3,723 views
- Last post 2016-02-13 19:07:02 by n2ri
208 unexplained Z-lift
by driggers
- 4 replies
- 2,420 views
- Last post 2016-02-10 17:41:38 by wardjr
209 error beds and extruder
by danielbmw
- 0 replies
- 951 views
- Last post 2016-02-10 14:23:47 by danielbmw
210 Solved calibrated steps/mm and extrusion multiplier... but overextrudes fill
by driggers
- 4 replies
- 2,883 views
- Last post 2016-02-10 13:15:06 by heartless