481 Solidoodle 3 housing, custom WAF proof!
by bnj
- 1 reply
- 1,617 views
- Last post 2014-04-15 16:17:11 by bnj
482 Enclosure from Ikea
by Zarni
- 14 replies
- 13,618 views
- Last post 2014-04-15 12:47:43 by billchurch
483 Just installed a board fan
by ease
- 2 replies
- 1,477 views
- Last post 2014-04-13 22:15:03 by ease
484 Best way to mount a QU-BD Bed?
by mloebl
- 17 replies
- 11,306 views
- Last post 2014-04-12 12:07:34 by adrian
485 What are the "must do" mods/hacks?
by aaronstalling
- 6 replies
- 2,918 views
- Last post 2014-04-12 12:02:48 by adrian
- 3 replies
- 2,044 views
- Last post 2014-04-10 01:45:49 by grob
- 76 replies
- 61,989 views
- Last post 2014-04-03 19:53:09 by wardjr
488 Firmware mods to rescue and resume failed prints
by tealvince
- 11 replies
- 12,151 views
- Last post 2014-04-02 00:02:02 by slimstar2
489 pulley wobble from wear
by slimstar2
- 2 replies
- 2,830 views
- Last post 2014-03-31 23:08:33 by slimstar2
490 My E3d bowden came with a surprise
by accusedmonk
- 4 replies
- 2,430 views
- Last post 2014-03-31 21:36:13 by accusedmonk
491 $150 Free Stuff from Misumi USA for new customers
by ggunners
- 11 replies
- 8,973 views
- Last post 2014-03-31 20:54:51 by piperpilot
492 How to Set EEPROMS for Pulley Setups
by Jeepguy42
- 6 replies
- 3,904 views
- Last post 2014-03-27 10:58:31 by Hazer
493 flashing firmware on 1286-au
by onlychild84
- 1 reply
- 1,458 views
- Last post 2014-03-26 08:12:48 by adrian
- 36 replies
- 38,991 views
- Last post 2014-03-25 17:57:32 by ysb
495 Third party heated bed
by harold3d
- 6 replies
- 3,975 views
- Last post 2014-03-21 14:57:31 by harold3d
496 SD4 android lcd screen
by Qvims
- 5 replies
- 4,419 views
- Last post 2014-03-21 14:04:57 by gtennefoss
497 Is 14v going into the Solidoodle 3 safe?
by Skyminer
- 2 replies
- 1,439 views
- Last post 2014-03-19 15:19:13 by elmoret
498 raspberry pi and solidoodle 2??
by Jonathan
- 6 replies
- 4,437 views
- Last post 2014-03-17 21:17:27 by agentsmith
499 Glass evenly heating
by janbeckman
- 12 replies
- 7,499 views
- Last post 2014-03-17 16:08:30 by wardjr
500 which firmware do i need
by dubbsd
- 11 replies
- 5,862 views
- Last post 2014-03-16 08:18:05 by adrian
- 52 replies
- 41,779 views
- Last post 2014-03-14 03:54:25 by MolecularConcept
502 A little help with updating firmware for E3D extruder and prntrboard
by michael.t.albers
- 2 replies
- 1,556 views
- Last post 2014-03-12 15:41:01 by michael.t.albers
503 P.E.T. tape instead of kapton .....?
by SnakeEyes
- 1 reply
- 1,954 views
- Last post 2014-03-07 21:10:03 by elmoret
504 Bed Z axis idea
by BFresh
- 2 replies
- 4,060 views
- Last post 2014-03-07 12:12:54 by Hazer
505 Fillerment Roller Lid
by lawsy
- 5 replies
- 4,048 views
- Last post 2014-03-06 21:26:39 by MolecularConcept
506 Z rod pitch+thread?
by AZERATE
- 2 replies
- 1,623 views
- Last post 2014-03-05 22:33:58 by AZERATE
507 Drying Out filament. Dehumidifying?
by SnakeEyes
- 9 replies
- 30,636 views
- Last post 2014-03-05 17:53:08 by Stevos758
508 question about a slicing software feature
by frozensoda
- 3 replies
- 1,476 views
- Last post 2014-03-03 21:13:22 by frozensoda
509 Vgroove vs shaft
by pcm81
- 4 replies
- 3,170 views
- Last post 2014-03-02 00:07:10 by danny
510 Manual controls
by Dandean
- 0 replies
- 940 views
- Last post 2014-03-01 19:42:27 by Dandean