661 Max hotend temp on SD4
by hy-bye
- 20 replies
- 12,205 views
- Last post 2014-07-25 23:23:44 by Miroule
662 Insane Solidoodle speeds
by Hazer
- 17 replies
- 10,376 views
- Last post 2014-07-24 12:46:49 by Tomek
663 Is the SoliDoodle 4 worthwhile?
by DarrellS
- 5 replies
- 2,711 views
- Last post 2014-07-24 04:35:06 by grob
664 bought used machine now what?
by devernham
- 5 replies
- 2,635 views
- Last post 2014-07-22 17:36:38 by shields1
665 extrudes in manual but not during printing
by srtaghavi
- 1 reply
- 893 views
- Last post 2014-07-22 07:09:51 by grob
- 25 replies
- 26,831 views
- Last post 2014-07-20 23:49:35 by LdyMox
667 skeinforge 4X slower than ETA
by TickTock
- 0 replies
- 1,588 views
- Last post 2014-07-20 17:38:03 by TickTock
668 Wrong solidoodle?
by ccorwin
- 4 replies
- 2,206 views
- Last post 2014-07-18 16:01:09 by KD
669 Today's The Day
by exineport
- 20 replies
- 11,244 views
- Last post 2014-07-17 15:54:00 by AZERATE
- 32 replies
- 20,175 views
- Last post 2014-07-17 04:33:51 by browner87
671 Should I upgrade?
by Ggalisky
- 1 reply
- 1,182 views
- Last post 2014-07-13 20:26:03 by wire10ga
672 what size are the three countersunk bed screws?
by Tomek
- 9 replies
- 5,413 views
- Last post 2014-07-08 03:55:24 by Tomek
673 PolyCarbonate / Lexan Build Platform Pro's Con's
by FordGalaxie
- 3 replies
- 5,710 views
- Last post 2014-07-04 13:57:12 by doppler
674 Preheating Material
by exineport
- 3 replies
- 1,630 views
- Last post 2014-07-04 00:48:21 by grob
675 SD2 with an IMac...
by Ski52
- 4 replies
- 2,829 views
- Last post 2014-07-03 14:33:19 by Ski52
676 Solidoodle 2 Pro - Dead on Arrival??
by bommers
- 10 replies
- 5,587 views
- Last post 2014-07-03 01:56:27 by bommers
- 71 replies
- 42,425 views
- Last post 2014-06-30 18:16:08 by AZERATE
678 Issue with rough prints
by cujo3131
- 4 replies
- 3,201 views
- Last post 2014-06-25 15:35:04 by wardjr
679Moved: Ninjaflex on Solidoodle?
by lcruz007
- No reply information
- No viewing information
- No last post information
680 PLA on a Solidoodle 4
by HobbyNumberNine
- 3 replies
- 2,358 views
- Last post 2014-06-21 18:42:21 by HobbyNumberNine
681 Vertical layers not adhering
by slinberg
- 3 replies
- 2,079 views
- Last post 2014-06-18 14:43:41 by wardjr
682 How to adjust Skeinforge acceleration
by TjckTock
- 1 reply
- 1,057 views
- Last post 2014-06-18 02:21:51 by TjckTock
683 Horizontal Perimeter Failing
by caswal
- 10 replies
- 7,363 views
- Last post 2014-06-14 05:42:07 by n2ri
684 Would this work as an accurate belt tension measuring device?
by aaronstalling
- 0 replies
- 875 views
- Last post 2014-06-13 10:10:58 by aaronstalling
- 1 reply
- 18,549 views
- Last post 2014-06-13 07:59:50 by n2ri
686 New to the hobby, seeking advice
by j.bradley90
- 2 replies
- 1,043 views
- Last post 2014-06-13 04:54:37 by j.bradley90
687 Good prints/ failed prints
by Ggalisky
- 14 replies
- 6,949 views
- Last post 2014-06-12 18:54:26 by LdyMox
688 SD3 new drive KIT
by pcm81
- 3 replies
- 1,868 views
- Last post 2014-06-12 18:25:25 by mdrVB6
689 repetier host ver 95f adding more slicers
by n2ri
- 0 replies
- 1,837 views
- Last post 2014-06-12 04:47:18 by n2ri
- 0 replies
- 1,615 views
- Last post 2014-06-10 07:12:18 by n2ri