- 26 replies
- 15,690 views
- Last post 2015-11-02 17:43:16 by heartless
- 26 replies
- 15,965 views
- Last post 2015-10-28 06:15:33 by ecalistro87
303 Curling and Bed Leveling
by Rocketman
- 5 replies
- 2,463 views
- Last post 2015-10-26 19:45:31 by pirvan
- 29 replies
- 16,860 views
- Last post 2015-10-26 01:51:08 by AZERATE
305 Bad prints
by dineshwong
- 11 replies
- 5,808 views
- Last post 2015-10-25 23:41:14 by dineshwong
306 so, it was all going great...
by switchblade5984
- 4 replies
- 2,038 views
- Last post 2015-10-22 16:20:40 by heartless
307 Can you PID tune a SSR controlled heat bed?
by Ski52
- 3 replies
- 5,427 views
- Last post 2015-10-20 16:32:19 by Ski52
308 (SD4) X axis not moving (post carriage upgrade + video)
by takadakeyo
- 7 replies
- 4,274 views
- Last post 2015-10-20 06:41:19 by takadakeyo
309 Odd issue...
by switchblade5984
- 14 replies
- 6,730 views
- Last post 2015-10-19 13:21:06 by heartless
310 Thermistor is not reading correct temperature for heated bed
by EMC2 Robo
- 22 replies
- 18,260 views
- Last post 2015-10-17 00:12:58 by carl_m1968
311 Solved SD4+E3Dv6=Printer stopped due to errors.
by RandomloserDK
- 19 replies
- 9,444 views
- Last post 2015-10-14 23:17:04 by capibara
312 Hot motor + Printer skipping along the board
by Thorarinn
- 9 replies
- 4,233 views
- Last post 2015-10-14 04:51:10 by wardjr
313 Help w/ SSR and Heated Bed
by fdm_process
- 6 replies
- 3,712 views
- Last post 2015-10-12 15:07:36 by Ski52
314 Heated bed takes an enormous time to warm up.
by paramite12
- 6 replies
- 3,684 views
- Last post 2015-10-12 00:31:54 by noslenwerdna
315 Surface quality & extrusion issues
by pirvan
- 14 replies
- 5,997 views
- Last post 2015-10-11 03:56:02 by wardjr
316 Do any others have a small lip on the bottom of their prints?
by carl_m1968
- 9 replies
- 12,387 views
- Last post 2015-10-09 21:56:58 by Tin Falcon
317 Help! Different sizes while printing the same on 2 printer
by GerriGold
- 5 replies
- 2,634 views
- Last post 2015-10-09 17:01:58 by mdrVB6
318 Extruder spits too much filament
by VonDriguen
- 10 replies
- 6,308 views
- Last post 2015-10-09 09:33:38 by VonDriguen
319 Questions about replacing Z-screw
by mmiller7
- 5 replies
- 4,140 views
- Last post 2015-10-08 20:15:06 by mmiller7
320 abs filament the doesnt flow
by shields1.as
- 4 replies
- 2,259 views
- Last post 2015-10-08 12:14:19 by heartless
321 SD2 Heat Pad Problem
by Ski52
- 23 replies
- 10,335 views
- Last post 2015-10-08 00:45:04 by Ski52
322 Squeaky noise
by Rocketman
- 4 replies
- 3,067 views
- Last post 2015-10-07 11:42:28 by heartless
323 Help! Extruder thermistor issues
by michaelosully268
- 7 replies
- 4,734 views
- Last post 2015-10-06 13:26:29 by michaelosully268
324 Da vinci AIO Error #14
by raptor700yfz
- 0 replies
- 958 views
- Last post 2015-10-06 00:16:19 by raptor700yfz
325 Repetier Error Message
by Rocketman
- 2 replies
- 1,490 views
- Last post 2015-10-05 16:58:42 by Rocketman
326 Help! SD4 new Motherboard options?
by JGPenland
- 8 replies
- 4,043 views
- Last post 2015-10-04 18:15:45 by heartless
327 Referb Solidoodle 3 motherboard?
by ianortiz956
- 8 replies
- 3,394 views
- Last post 2015-10-02 03:43:14 by wardjr
328 (SD4) Help with X carriage upgrade (Lawsy and modded X carriage) Pics
by takadakeyo
- 12 replies
- 5,262 views
- Last post 2015-10-01 20:33:53 by lueman
329 e3d v6 upgrade Heat issue
by talsiri
- 3 replies
- 1,762 views
- Last post 2015-10-01 05:48:37 by wardjr
330 Help! I believe the X axis is shifting every so many layers during print.
by jrclemens
- 5 replies
- 2,644 views
- Last post 2015-09-29 18:56:18 by jagowilson