361 mexhmixer 2.1 is out..
by ysb
- 1 reply
- 1,312 views
- Last post 2014-02-19 18:19:52 by ggunners
362 Error M999
by Cyber-Monkey
- 6 replies
- 4,746 views
- Last post 2014-02-18 22:33:47 by SnakeEyes
363 KISSlicer going down the rabbit hole.....
by pirvan
- 9 replies
- 5,355 views
- Last post 2014-02-18 16:08:24 by IanJohnson
364 Slic3r config question.
by Antron007
- 1 reply
- 1,136 views
- Last post 2014-02-18 02:43:45 by ronsii
365 New Repetier Host 0.95b
by muddtt
- 23 replies
- 18,521 views
- Last post 2014-02-09 18:49:02 by knowack
366 Simplify3D - Anyone using it?
by pirvan
- 14 replies
- 19,560 views
- Last post 2014-02-09 18:30:02 by kobi-s
367 Raspberry pi 2.8" LCD Touchscreen
by COASTER19
- 3 replies
- 3,585 views
- Last post 2014-02-01 17:21:08 by COASTER19
368 Asymmetric steps for threadless ball screw in new firmware
by Rincewind
- 6 replies
- 4,711 views
- Last post 2014-02-01 04:04:33 by BlackestofOz
369 Need urgent help with setting up my new Solidoodle 3!
by TheDoctor
- 2 replies
- 2,167 views
- Last post 2014-01-31 10:54:12 by ThatGuy
370 install issue with Repetier V0.95F
by GrJimmy
- 17 replies
- 12,460 views
- Last post 2014-01-31 00:36:40 by wardjr
371 Power supply during firmware upload
by satman49
- 7 replies
- 3,840 views
- Last post 2014-01-28 23:11:11 by tealvince
372 I can't find this Solidoodle3 .1mm.ini SOFTWARE
by WORF22
- 1 reply
- 1,404 views
- Last post 2014-01-27 19:25:33 by satman49
- 2 replies
- 1,827 views
- Last post 2014-01-22 16:43:50 by Jukalo
374 ReptierHost 0.95+ No longer Open Source
by adrian
- 2 replies
- 2,793 views
- Last post 2014-01-21 09:47:05 by bethlewis733
375 Solidoodle 3 Firmware?
by CrazyBear
- 14 replies
- 22,514 views
- Last post 2014-01-20 06:07:38 by nb
376 .08 Slic3r setting?
by AZERATE
- 5 replies
- 2,850 views
- Last post 2014-01-20 02:01:10 by jawhn
377 Semi-dedicated computer?
by BlaiddDrwg
- 1 reply
- 1,454 views
- Last post 2014-01-17 18:06:07 by AZERATE
378 Centering objects on bed?
by Claghorn
- 4 replies
- 3,120 views
- Last post 2014-01-10 18:35:54 by satman49
379 Unwanted Pause on Repeiter Server
by aaronboo
- 0 replies
- 3,943 views
- Last post 2014-01-04 02:40:53 by aaronboo
380 Repetier-host v095c Sequential printing issue
by RavensCrest
- 4 replies
- 4,838 views
- Last post 2014-01-04 02:23:10 by RavensCrest
381 Firmware, Clacking, Eeprom, Oh My!
by Claghorn
- 2 replies
- 1,715 views
- Last post 2014-01-03 02:26:17 by Claghorn
382 Pre-compiled firmware?
by Claghorn
- 2 replies
- 9,620 views
- Last post 2014-01-01 19:23:09 by Claghorn
383 Help with rafts
by tycoonman1
- 20 replies
- 12,495 views
- Last post 2013-12-29 19:46:53 by tycoonman1
384 Printrboard Rev E on Repeiter Server
by aaronboo
- 1 reply
- 1,397 views
- Last post 2013-12-27 08:04:23 by ronsii
385 Changing fill angle in Slic3r
by tycoonman1
- 0 replies
- 1,786 views
- Last post 2013-12-23 04:47:58 by tycoonman1
386 Need Help with software
by allanme79
- 6 replies
- 3,010 views
- Last post 2013-12-20 13:09:40 by allanme79
387 Revert to older firmware
by satman49
- 1 reply
- 1,546 views
- Last post 2013-12-19 01:44:16 by wardjr
388 Slic3r 1.0.0RC1 is out
by spapadim
- 11 replies
- 6,172 views
- Last post 2013-12-14 03:10:32 by KevlarGorilla
389 Is there any software out there for estimating filament used?
by JustSomeGuyTN
- 4 replies
- 2,744 views
- Last post 2013-12-11 15:50:17 by JustSomeGuyTN
390 extruder anchor
by satman49
- 5 replies
- 2,809 views
- Last post 2013-12-11 03:38:29 by satman49