541 Zortrax M200 3D printer and Zortax filament
by office
- 0 replies
- 1,093 views
- Last post 2015-12-04 14:12:10 by office
542 printer choice - advice
by jfrost
- 0 replies
- 924 views
- Last post 2015-12-02 14:43:37 by jfrost
543 am i looking in the right places
by stevenhohenstein
- 0 replies
- 764 views
- Last post 2015-12-02 01:45:36 by stevenhohenstein
544 CTC Dual, layer issue?
by jevans3d
- 8 replies
- 4,032 views
- Last post 2015-11-30 21:53:51 by ggunners
545 GCode
by poppinfresh
- 1 reply
- 1,391 views
- Last post 2015-11-24 03:50:41 by grob
546 XYZ 1.0 PRINTER HEATED SURFACE REPLACEMENT CALIBRATION ISSUE
by VINNYTHEDOG
- 3 replies
- 1,931 views
- Last post 2015-11-19 20:26:26 by carl_m1968
547 New DLP Printer with the LARGEST build volume on the market
by Blackbobgie
- 2 replies
- 33,304 views
- Last post 2015-11-19 18:12:52 by pirvan
548 Thermister variability in E3D-V6 hot end
by cliquot22
- 5 replies
- 2,693 views
- Last post 2015-11-18 18:35:20 by cliquot22
549 Little Help w/ Some Research
by cummingscha
- 1 reply
- 1,333 views
- Last post 2015-11-13 15:46:51 by widespreaddeadhead
550 Does any one have any thing to say about a HICTOP or a Prusa?
by jmap2112
- 14 replies
- 38,819 views
- Last post 2015-11-11 05:45:48 by slimjim2222
551 Big printer
by Landin81
- 0 replies
- 1,759 views
- Last post 2015-11-10 01:37:29 by Landin81
552 Anyone use or have experience with XTC-3D coating
by 11b30b4
- 3 replies
- 2,589 views
- Last post 2015-11-07 16:46:04 by pirvan
553 CTC modded and perfect now.
by carl_m1968
- 11 replies
- 17,746 views
- Last post 2015-11-02 19:37:17 by heartless
554 Elmers Purple Disappearing Glue - print stuck hard to glass bed
by joeytwomugs
- 7 replies
- 53,287 views
- Last post 2015-11-02 18:29:20 by heartless
555 CTC - display reads heating even though temp reads ok?
by joeytwomugs
- 4 replies
- 2,217 views
- Last post 2015-10-29 19:04:34 by joeytwomugs
556 Bad Y axis layer shift problem can't figure out
by hansen644
- 14 replies
- 6,886 views
- Last post 2015-10-26 21:46:39 by chriszyl
- 34 replies
- 16,100 views
- Last post 2015-10-24 20:47:57 by joeytwomugs
558 Help? Solidoodle Press Grind
by awesomedonut
- 1 reply
- 911 views
- Last post 2015-10-22 06:32:46 by madfalcon81
559 da Vinci Duo 2.0 Extruder Problems
by tylersong55
- 13 replies
- 6,639 views
- Last post 2015-10-22 03:20:20 by tylersong55
560 Airwolf3D printers... careless quality checks?
by josh.aeauto
- 12 replies
- 6,434 views
- Last post 2015-10-15 19:24:51 by jagowilson
561 BEWARE CTC PRINTER
by lbcr1
- 15 replies
- 15,330 views
- Last post 2015-10-14 21:15:44 by carl_m1968
562 HICTOP prusa i3 - Assembly questions
by dineshwong
- 15 replies
- 13,537 views
- Last post 2015-10-11 02:51:51 by dineshwong
563 My RAMPS 1.4 is not connecting to my computer
by vincentwoodward4
- 0 replies
- 5,446 views
- Last post 2015-10-10 19:07:19 by vincentwoodward4
564 ball screws or lead screws
by ryan-mm85
- 12 replies
- 8,094 views
- Last post 2015-10-06 05:13:31 by grob
565 GeeTech Me Creator Solidoodle 2 Clone
by KWICK
- 21 replies
- 24,867 views
- Last post 2015-10-05 01:21:22 by KWICK
- 26 replies
- 15,377 views
- Last post 2015-10-04 13:37:39 by heartless
567 multiple printers
by zburhop
- 8 replies
- 4,078 views
- Last post 2015-10-04 03:45:31 by AZERATE
568 delta hotend pendulum affect?
by r_tuttle
- 5 replies
- 2,699 views
- Last post 2015-09-20 21:42:38 by r_tuttle
569 Kossel Mini Modifcation
by jmap2112
- 11 replies
- 5,573 views
- Last post 2015-09-17 01:49:51 by r_tuttle
570 KISSlicer not abandoned
by IanJohnson
- 2 replies
- 2,155 views
- Last post 2015-09-13 17:26:22 by metaldrgn