- 26 replies
- 19,116 views
- Last post 2015-06-05 03:44:31 by carl_m1968
212 Extruder Cabling on SD4
by Zortwil
- 2 replies
- 1,721 views
- Last post 2015-06-04 01:44:56 by Zortwil
213 Why Rumba on SD 4 and which stepper drivers?
by sanguish
- 20 replies
- 10,760 views
- Last post 2015-06-03 13:14:19 by heartless
214 Fan duct/mount for E3D v6 addon w/ OE extruder housing
by metaldrgn
- 22 replies
- 14,910 views
- Last post 2015-06-03 04:37:27 by metaldrgn
215 Flashing Firmware for new E3D - Is it necessary?
by pirvan
- 9 replies
- 6,377 views
- Last post 2015-06-02 01:45:33 by wardjr
216 4123D's Solidoodle 4 Aluminum Rebuild
by apetrosky
- 6 replies
- 4,612 views
- Last post 2015-05-28 00:58:42 by bnj
217 All Metal Hot End (NOT E3D)
by pirvan
- 19 replies
- 12,883 views
- Last post 2015-05-27 17:37:41 by IronMan
218 Vertical striping (not Z-wobble) possible solution
by metaldrgn
- 9 replies
- 6,979 views
- Last post 2015-05-26 06:03:14 by grob
219 Threaded pulley for braid line
by TheBaron
- 4 replies
- 3,190 views
- Last post 2015-05-22 12:56:58 by TheBaron
220 M3 Hardware
by Zortwil
- 2 replies
- 1,472 views
- Last post 2015-05-20 18:31:18 by mdrVB6
221 Another belt tension method
by mdrVB6
- 0 replies
- 1,361 views
- Last post 2015-05-20 18:25:16 by mdrVB6
- 8 replies
- 15,293 views
- Last post 2015-05-19 01:52:13 by grob
223 New e3d v6 nozzle fan
by shields1.as
- 3 replies
- 1,554 views
- Last post 2015-05-18 14:13:46 by TheBaron
224 Adding stand alone print capability
by Trevor.James
- 9 replies
- 5,470 views
- Last post 2015-05-18 13:08:55 by TheBaron
225 SD4 horizontal stripes on prints
by mdonci
- 3 replies
- 2,313 views
- Last post 2015-05-17 00:42:16 by heartless
226 The Ultimate Upgrade Guide (Work in Progress)
by fran.cuesta.marin
- 6 replies
- 4,900 views
- Last post 2015-05-16 19:06:37 by blarz
227 Lawsy Carriages questions
by blarz
- 20 replies
- 10,653 views
- Last post 2015-05-13 19:15:23 by blarz
228 RTV silicone for thermister?
by TheBaron
- 6 replies
- 31,532 views
- Last post 2015-05-13 18:47:30 by TheBaron
229 X Axis problem since Lawsy Carriage install
by blarz
- 8 replies
- 4,965 views
- Last post 2015-05-07 20:15:40 by TheBaron
230 Replacing all the stepper motors
by sanguish
- 19 replies
- 11,408 views
- Last post 2015-05-06 14:05:56 by TheBaron
231 (Help) Octoprint Running Prints Slow
by fdm_process
- 0 replies
- 1,468 views
- Last post 2015-05-02 17:36:21 by fdm_process
232 PID for bed heater?
by w_smith
- 3 replies
- 2,628 views
- Last post 2015-05-01 17:42:42 by jagowilson
233 New Fan installation Success's... and Failures.....
by TinkerT
- 0 replies
- 993 views
- Last post 2015-04-28 01:18:16 by TinkerT
234 Anyone do a Dual E3Dv6 upgrade?
by patrick.w.york
- 10 replies
- 5,383 views
- Last post 2015-04-23 18:31:21 by jagowilson
235 Where to mount new Powersupply?
by sanguish
- 9 replies
- 5,071 views
- Last post 2015-04-23 16:55:24 by sanguish
236 Y-Axis- Issues and solution(s)
by dsmith1912
- 1 reply
- 1,615 views
- Last post 2015-04-23 12:02:27 by mdrVB6
237 Dual bed heaters ???? Any thoughts?
by slimstar2
- 3 replies
- 2,619 views
- Last post 2015-04-22 22:55:38 by slimstar2
238 New efficient/easy/true anti-backlash configuration.
by metaldrgn
- 1 reply
- 1,323 views
- Last post 2015-04-22 04:57:00 by metaldrgn
239 Implementing the RepRap Industrial belt tensioner into lawsy carriages
by chancrescolex
- 0 replies
- 6,007 views
- Last post 2015-04-21 22:30:18 by chancrescolex
240 Backlash fix - z rod pushing well nut out
by chente922
- 10 replies
- 6,681 views
- Last post 2015-04-21 22:28:49 by metaldrgn