241 Slic3r vs. Cura
by Torque
- 2 replies
- 3,761 views
- Last post 2015-02-11 13:52:23 by ysb
242 CraftWare 1.0b
by hjani1970
- 16 replies
- 14,100 views
- Last post 2015-02-08 22:59:46 by tonycstech
243 Changing Extruder Temp During Print with Mattercontrol
by CrazyCat
- 0 replies
- 2,137 views
- Last post 2015-02-08 21:27:57 by CrazyCat
244 lil help with Blender please
by n2ri
- 0 replies
- 1,268 views
- Last post 2015-02-05 02:58:11 by n2ri
245 Removing a part, midprint
by theBLOCK
- 1 reply
- 1,439 views
- Last post 2015-02-04 23:37:16 by DePartedPrinter
246 Is there a nice graphic gcode editor?
by macouno
- 9 replies
- 10,121 views
- Last post 2015-02-04 09:18:22 by nobias
247 "MINTEMP" error on SD3 prevents print
by renesaucedo333
- 7 replies
- 5,815 views
- Last post 2015-02-02 11:02:29 by IronMan
248 [SOLVED] M98 and M99 backlash compensation commands?
by redbarret
- 11 replies
- 11,104 views
- Last post 2015-01-28 02:04:28 by Dream-Cypher
249 how do I open an lwo file and export to stl?
by n2ri
- 1 reply
- 2,277 views
- Last post 2015-01-27 14:36:01 by ysb
250 Netfabb cloud dead?
by Serin
- 2 replies
- 2,166 views
- Last post 2015-01-27 10:20:02 by Serin
251 saving Gcode vers stl files in folders
by n2ri
- 2 replies
- 3,500 views
- Last post 2015-01-27 03:34:22 by n2ri
252 port for mac
by davidalane
- 1 reply
- 1,299 views
- Last post 2015-01-26 00:25:30 by davidalane
253 repetier 0.92 on xyz. at a loss
by davidalane
- 0 replies
- 1,391 views
- Last post 2015-01-24 02:53:01 by davidalane
254 Repetier firmware
by davidalane
- 0 replies
- 1,350 views
- Last post 2015-01-21 23:26:17 by davidalane
255 Da vinci firmware hack
by davidalane
- 4 replies
- 3,376 views
- Last post 2015-01-19 04:06:49 by davidalane
256 Geeetech board in printrbot XL mirrors prints no matter what Ive tried
by Rockcrawljeep999
- 0 replies
- 1,188 views
- Last post 2015-01-15 06:04:25 by Rockcrawljeep999
257 G code from Makerware to print in Replicator G
by Accessdenied
- 0 replies
- 1,591 views
- Last post 2015-01-13 14:53:03 by Accessdenied
258 Bed center is incorrect (way off)
by jaques
- 21 replies
- 19,500 views
- Last post 2015-01-01 22:11:51 by gregsw
259 firmware and out of filament support?
by Claghorn
- 3 replies
- 2,169 views
- Last post 2014-12-29 19:47:17 by Claghorn
260 Closed: Beginner question about Slic3r
by takadakeyo
- 0 replies
- 1,208 views
- Last post 2014-12-27 20:43:17 by takadakeyo
261 Blender3D dimensions
by redbarret
- 3 replies
- 2,169 views
- Last post 2014-12-19 05:44:22 by redbarret
262 slic3r can't handle valid model?
by Claghorn
- 7 replies
- 4,836 views
- Last post 2014-12-16 01:47:59 by Claghorn
263 A question about slic3r.
by lin6499
- 3 replies
- 2,447 views
- Last post 2014-12-14 04:05:31 by lin6499
264 3D software
by oneleg
- 8 replies
- 5,152 views
- Last post 2014-12-13 01:15:21 by dave.lantz
265 Question about 3d Printing software/ firmware
by slakjak1215
- 1 reply
- 1,338 views
- Last post 2014-12-13 00:24:57 by justsomeguy
266 Massively Improved Bed Temp Stability if you enable PID!
by adrian
- 9 replies
- 54,040 views
- Last post 2014-12-05 23:01:16 by boksbox
267 Rings on your fingers...(bracelets too)
by owenransen
- 0 replies
- 1,094 views
- Last post 2014-11-30 07:23:23 by owenransen
268 Octoprint - that's pretty neat!
by elmoret
- 12 replies
- 18,980 views
- Last post 2014-11-23 03:56:17 by knowack
269 OSX Slic3r config files for SD4?
by w_smith
- 0 replies
- 1,142 views
- Last post 2014-11-23 01:25:57 by w_smith
270 Slicer Infill problem
by justsomeguy
- 7 replies
- 4,269 views
- Last post 2014-11-22 20:21:18 by wardjr