You are not logged in. Please login or register.
SoliForum - 3D Printing Community → Help/Repair/Maintenance → E3d upgrade help
Have sd2, installed e3d extruder ,thermistor and new power supply. I tried to download all new firmware and haven't been able to get past first base. Seems like I'm going backwards. I would be willing to ship printer,laptop to someone to get it up and running. I know how to use repieter and all that but can't get the programming needed on this upgrade Quote me the cost
It was a pain in the butt for me too. Make sure you have the right version of arduino and
when you import the marlin file there was a thing or 2 that had to be changed. Once I got that down I was ok.
Have sd2, installed e3d extruder ,thermistor and new power supply. I tried to download all new firmware and haven't been able to get past first base. Seems like I'm going backwards. I would be willing to ship printer,laptop to someone to get it up and running. I know how to use repieter and all that but can't get the programming needed on this upgrade Quote me the cost
Have sd2, installed e3d extruder ,thermistor and new power supply. I tried to download all new firmware and haven't been able to get past first base. Seems like I'm going backwards. I would be willing to ship printer,laptop to someone to get it up and running. I know how to use repieter and all that but can't get the programming needed on this upgrade Quote me the cost
What board do you have? Once we know that we can point you to the step by step instructions.
If after that, if you still can't figure it out I'll do it but you'll have to remove the board and ship it to me.
if you still can't figure it out I'll do it but you'll have to remove the board and ship it to me.
What a guy! 
wardjr wrote:if you still can't figure it out I'll do it but you'll have to remove the board and ship it to me.
What a guy!
Says the guy stuck using my old Sang 
Thnkx for help
Have ATMega 644P
Running rep .95
Does your board say Sanguinololu Rev 1.3 on it?
What version of arduino are you using?
Are you using the instructions from the WIKI?
What step are you stuck at?
Soliwiki instructions
Couldn't fi which San board
Arduino 0022. But could not get it to work
I guess every thing having to do with firmware printer update process
After installing new hot end I downloaded repitier update since I had never updated since I got printer originally. I was able to move print head x and y. But after that I cannot even do that
New power supply does work as I have power to fan. Should I delete all downloads and repitier And start all over from scratch. Seem like there's so much stuff in download folder.
This is a Printrboard
This is a Sanguinololu
No need to delete anything. RH would have zero accountability for your experiences.
The best place to start is by identifying which board you have.
In wiki instructions it say that soliddoodle always put their own label over processor number, so I peeled it off to get number underneath. Underneath is # ATMega 664P I got sd2 1/1/13
I just looked to see if I still have label and could not find.
Pretty sure you have a sang board
In wiki instructions it say that soliddoodle always put their own label over processor number, so I peeled it off to get number underneath. Underneath is # ATMega 664P I got sd2 1/1/13
I just looked to see if I still have label and could not find.
Pretty sure you have a sang board
Dandean wrote:In wiki instructions it say that soliddoodle always put their own label over processor number, so I peeled it off to get number underneath. Underneath is # ATMega 664P I got sd2 1/1/13
I just looked to see if I still have label and could not find.
+1
SoliForum - 3D Printing Community → Help/Repair/Maintenance → E3d upgrade help
Powered by PunBB, supported by Informer Technologies, Inc.
