1 Topic by forme128

  • forme128
  • Newbie
  • Offline
  • Registered: 2013-02-26
  • Posts: 4

Topic: Solidoodle printing but gets off its own path

Prints an object incorrectly every time except for extremely small pieces. After printing a footprint it starts getting more off of its path each time? Had repetier host then switched to pronterface. I just got my solidoodle. First time printer user. I think it may be settings on software I am not sure. I am running on windows 7 but I dual boot with linux and have access to other pc's. I hope its a software issue big_smile

Post's attachments

correctly printed.jpg
correctly printed.jpg 56.06 kb, file has never been downloaded. 

off footprint.jpg
off footprint.jpg 60.36 kb, file has never been downloaded. 

You don't have the permssions to download the attachments of this post.

2 Reply by 3D_UA (edited by 3D_UA 2013-02-26 18:14:20)

  • 3D_UA
  • Member
  • Offline
  • From: Ukraine
  • Registered: 2013-01-17
  • Posts: 40

Re: Solidoodle printing but gets off its own path

Check voltage at the motor drivers, as indicated here: http://www.solidoodle.com/how-to-2/troubleshooting/

http://www.solidoodle.com/wp-content/uploads/2012/01/Picture4small-300x200.jpg

Proper Voltages
X axis: .443
Y axis: .520
Z axis: .500
Extruder: .192

And check the free carriage stroke in X and Y axes with the power off.

3D_UA's Website

3 Reply by forme128

  • forme128
  • Newbie
  • Offline
  • Registered: 2013-02-26
  • Posts: 4

Re: Solidoodle printing but gets off its own path

Before I even took my multimeter out, i tried heating the extruder again, and now it will not heat up.

4 Reply by cmetzel

  • cmetzel
  • Member
  • Offline
  • From: Solidoodle2 #0091
  • Registered: 2012-08-22
  • Posts: 1,429

Re: Solidoodle printing but gets off its own path

Make sure all your set screws are tight on the pulleys and that you can move your print head around without binding with the power off.  Some alignment and belt tensioning may be needed

5 Reply by forme128

  • forme128
  • Newbie
  • Offline
  • Registered: 2013-02-26
  • Posts: 4

Re: Solidoodle printing but gets off its own path

It moves freely, as do the belts. Well the pcb let off a bit of smoke, now my usb controller doesnt recognize the solidoodle. I hope something didnt go out.  I was expecting an out of box experience. I hope i can trouble shoot this thing but i will need some assistance in real time, hopefully through skype with solidoodle.

6 Reply by forme128

  • forme128
  • Newbie
  • Offline
  • Registered: 2013-02-26
  • Posts: 4

Re: Solidoodle printing but gets off its own path

Ok solidoodle responding to pc again. Phew..... Reintalled usb controller drivers and let the solidoodle sit a while.

7 Reply by jjcuff1

  • jjcuff1
  • Member
  • Offline
  • Registered: 2012-10-18
  • Posts: 253

Re: Solidoodle printing but gets off its own path

Ever figure htings out?

I did the voltage thing all of mine were lower then posted BUT I talked to SD and they said that might be ok I could be overdriving if I am not binding. i will checking binding one more time then lower things down a notch and see.

SD2 owner- Surestepr, filament holder,QUBD servo and heaters, glass bed
Print for fun and for parts for my sports cars
current car is 88 IROC