1 Topic by efes

  • efes
  • Member
  • Offline
  • From: Belgium
  • Registered: 2015-06-13
  • Posts: 110

Topic: s3d configured ?

hello, I use S3D shoulders and neck not very well printed, how well configured? thank you

attach FFF setup s3d

Post's attachments

20150623_205120 [800x600].jpg
20150623_205120 [800x600].jpg 22.5 kb, 1 downloads since 2015-06-23 

20150623_205130 [800x600].jpg
20150623_205130 [800x600].jpg 23.02 kb, file has never been downloaded. 

20150623_205212 [800x600].jpg
20150623_205212 [800x600].jpg 36.1 kb, file has never been downloaded. 

20150623_205300 [800x600].jpg 36.16 kb, file has never been downloaded. 

womanbody.fff 9.33 kb, 3 downloads since 2015-06-23 

You don't have the permssions to download the attachments of this post.
davinci 1.0
firmware repetier

2 Reply by IronMan

  • IronMan
  • IronMan
  • PRINTiT
  • Offline
  • From: SC
  • Registered: 2012-09-14
  • Posts: 1,269

Re: s3d configured ?

Seems like you are under-extruding a bit...try bumping up your Extrusion Multiplier...

Also, you should do a single-wall calibration cube every time you switch filament.

SD2 - Stock - Enclosure - Heated Bed - Glass Plate - Auto Fire Extinguisher
Ord Bot Hadron - RAMPS 1.4 - Bulldog XL - E3D v6 - 10" x 10" PCB Heated Build w/SSR - Glass Plate
Thanks for All of Your Help!

3 Reply by efes

  • efes
  • Member
  • Offline
  • From: Belgium
  • Registered: 2015-06-13
  • Posts: 110

Re: s3d configured ?

IronMan wrote:

Seems like you are under-extruding a bit...try bumping up your Extrusion Multiplier...

Also, you should do a single-wall calibration cube every time you switch filament.

I have 1,0 I need to increase maximum how much?

Post's attachments

ext01.jpg
ext01.jpg 127.72 kb, file has never been downloaded. 

You don't have the permssions to download the attachments of this post.
davinci 1.0
firmware repetier

4 Reply by scobo

  • scobo
  • scobo
  • Member
  • Offline
  • From: Scotland - UK
  • Registered: 2014-08-09
  • Posts: 993

Re: s3d configured ?

1.10 works well for me.

Davinci 1.0 with repetier firmware & E3D V6 Lite
Anycubic Photon DLP printer, Einscan-S 3D scanner
Simplify3d, 123D Design, Meshmixer
http://www.thingiverse.com/scobo/designs

5 Reply by IronMan

  • IronMan
  • IronMan
  • PRINTiT
  • Offline
  • From: SC
  • Registered: 2012-09-14
  • Posts: 1,269

Re: s3d configured ?

First of all, your Extrusion Width is set to 0.50...it should be 0.48; then follow the steps outlined here:

https://solidoodletips.wordpress.com/20 … flow-rate/

The above was done for a 0.35 dia. nozzle, but the calculations / adjustment procedures are the same...

SD2 - Stock - Enclosure - Heated Bed - Glass Plate - Auto Fire Extinguisher
Ord Bot Hadron - RAMPS 1.4 - Bulldog XL - E3D v6 - 10" x 10" PCB Heated Build w/SSR - Glass Plate
Thanks for All of Your Help!