1 Topic by jonzerb

  • jonzerb
  • Member
  • Offline
  • Registered: 2015-01-20
  • Posts: 195

Topic: Reset button for Press motherboard?

I cant figure out this final step for flashing new firmware to my Press with the new E3dV6 hot end i just installed. 

-JP1 is the boot jumper
http://i39.photobucket.com/albums/e164/zerrb/JP6%20jumper_zpslnrzgrwv.jpg

go to load the new firmware via BootloaderHID and this is what i get in the command prompt.
http://i39.photobucket.com/albums/e164/zerrb/Command%20Prompt_zps4yfw2hxt.jpg

on the wiki that im following it states that you need to press the RESET button on the board, but there isnt one.  so im lost.

2 Reply by slimstar2 (edited by slimstar2 2015-02-28 00:01:14)

  • slimstar2
  • slimstar2
  • Member
  • Offline
  • From: North Providence Rhode Island
  • Registered: 2014-03-28
  • Posts: 144

Re: Reset button for Press motherboard?

The wiki you are following is for the SD printrboard REV E  I am guessing. I believe you are using the new board REV CA   from what I see of your board  they are not the same   The jumpers pins are in the right lower corner of main chip and reset button is in the lower left corner of the board below SD card slot on my board. A picture of your whole board might help

Post's attachments

P2270064.JPG
P2270064.JPG 68.81 kb, file has never been downloaded. 

You don't have the permssions to download the attachments of this post.
SD3, RAMPS 1.4, Lawsy's carriages modified by me, 2 SSRs, E3D V6, 2 Power supplies, Independent monitoring of both power supplies (amps and volts) also extruder and bed temps, Blue Tooth connectivity, bearings in all axis & rotational points, Y axis direct drive.  Remotely controlled power box on / off . Gecko Tec build plate . Renamed FrankenDoodle

3 Reply by jonzerb (edited by jonzerb 2015-02-28 00:07:53)

  • jonzerb
  • Member
  • Offline
  • Registered: 2015-01-20
  • Posts: 195

Re: Reset button for Press motherboard?

You are correct on all points.

Thus my post asking how one would RESET this board, since there is no physical button as far as I can see.

4 Reply by jonzerb

  • jonzerb
  • Member
  • Offline
  • Registered: 2015-01-20
  • Posts: 195

Re: Reset button for Press motherboard?

Here are some pics. http://i39.photobucket.com/albums/e164/zerrb/20150227_190947_zpssxpuvvaf.jpghttp://i39.photobucket.com/albums/e164/zerrb/20150227_191000_zpsfq630tpu.jpg

5 Reply by slimstar2

  • slimstar2
  • slimstar2
  • Member
  • Offline
  • From: North Providence Rhode Island
  • Registered: 2014-03-28
  • Posts: 144

Re: Reset button for Press motherboard?

Thats the 1st time I 've seen that board . I would suggest calling Solidoodle tech support to ask them how to upload to that board and please tell to rest of us.

SD3, RAMPS 1.4, Lawsy's carriages modified by me, 2 SSRs, E3D V6, 2 Power supplies, Independent monitoring of both power supplies (amps and volts) also extruder and bed temps, Blue Tooth connectivity, bearings in all axis & rotational points, Y axis direct drive.  Remotely controlled power box on / off . Gecko Tec build plate . Renamed FrankenDoodle

6 Reply by jonzerb

  • jonzerb
  • Member
  • Offline
  • Registered: 2015-01-20
  • Posts: 195

Re: Reset button for Press motherboard?

Well, I would be more then glad to do that. I just can't find their number. And emails don't go returned for longer then i want to wait to "schedule" a phone call

7 Reply by slimstar2

  • slimstar2
  • slimstar2
  • Member
  • Offline
  • From: North Providence Rhode Island
  • Registered: 2014-03-28
  • Posts: 144

Re: Reset button for Press motherboard?

This is the phone # I used several months ago last time I needed support 1-347-464-0270

SD3, RAMPS 1.4, Lawsy's carriages modified by me, 2 SSRs, E3D V6, 2 Power supplies, Independent monitoring of both power supplies (amps and volts) also extruder and bed temps, Blue Tooth connectivity, bearings in all axis & rotational points, Y axis direct drive.  Remotely controlled power box on / off . Gecko Tec build plate . Renamed FrankenDoodle

8 Reply by slimstar2

  • slimstar2
  • slimstar2
  • Member
  • Offline
  • From: North Providence Rhode Island
  • Registered: 2014-03-28
  • Posts: 144

Re: Reset button for Press motherboard?

This is the phone # I used several months ago last time I needed support 1-347-464-0270

SD3, RAMPS 1.4, Lawsy's carriages modified by me, 2 SSRs, E3D V6, 2 Power supplies, Independent monitoring of both power supplies (amps and volts) also extruder and bed temps, Blue Tooth connectivity, bearings in all axis & rotational points, Y axis direct drive.  Remotely controlled power box on / off . Gecko Tec build plate . Renamed FrankenDoodle

9 Reply by jonzerb

  • jonzerb
  • Member
  • Offline
  • Registered: 2015-01-20
  • Posts: 195

Re: Reset button for Press motherboard?

Awesome. Thank you.