Re: SOLVED-Print layers look like Ramen noodles
I just noticed, where did your mk2 heatbed go?
I hope you're not mistaking MK5 extruder for an MK2 heatbed and thinking of upgrading because of that.
Solidoodle 4
26 2015-01-23 07:44:15 (edited by redbarret 2015-01-23 07:45:41)
- OneMoreCast
- Member
- Offline
Re: SOLVED-Print layers look like Ramen noodles
Bumped flowrate up, and feedrate down...woohoo
"All your base are belong to us." SD4 with a RUMBA, supernight PS, 40mm fan on X motor, lawsey carriages with new better tolerance rods, flanged rear bearings, new NEMA 17 with leadscrew on Z-Axis, and e3d v6 with MK5.
Ward and Jago are my heroes
Ward and Jago are my heroes
28 2015-01-23 08:00:26 (edited by OneMoreCast 2015-01-23 08:01:21)
- OneMoreCast
- Member
- Offline
Re: SOLVED-Print layers look like Ramen noodles
No red, i had too many problems at one time, i wanted to get the excess height and unevenness out of it (take away mk2 for now) to troubleshoot. Wanted as few variables as possible, to eliminate either something I did ie adding MK2 or software or stock part wise.
"All your base are belong to us." SD4 with a RUMBA, supernight PS, 40mm fan on X motor, lawsey carriages with new better tolerance rods, flanged rear bearings, new NEMA 17 with leadscrew on Z-Axis, and e3d v6 with MK5.
Ward and Jago are my heroes
Ward and Jago are my heroes
Re: SOLVED-Print layers look like Ramen noodles
Good logic.
But I think your putting a bandaid on your extrusion issue with that, not fixing it.
Solidoodle 4
- OneMoreCast
- Member
- Offline
Re: SOLVED-Print layers look like Ramen noodles
redbarret wrote:
Good logic.
But I think your putting a bandaid on your extrusion issue with that, not fixing it.
Whats the fix!? I thought tinkering settings was
"All your base are belong to us." SD4 with a RUMBA, supernight PS, 40mm fan on X motor, lawsey carriages with new better tolerance rods, flanged rear bearings, new NEMA 17 with leadscrew on Z-Axis, and e3d v6 with MK5.
Ward and Jago are my heroes
Ward and Jago are my heroes
31 2015-01-29 02:32:39 (edited by cpsmicahel 2015-01-29 02:33:16)
Re: SOLVED-Print layers look like Ramen noodles
OneMoreCast
Bumped flowrate up, and feedrate down...woohoo
can you screen shot what you changed so i can make sure i am in the right place i have that problem too
• Solidoodle Workbench Apprentice
• Creates plastic parts up to 6" x 6" x 8"
• Heated Aluminum Build Platform with Glass Bed
• Dual extruder
• Creates plastic parts up to 6" x 6" x 8"
• Heated Aluminum Build Platform with Glass Bed
• Dual extruder
32 2015-01-29 03:40:02 (edited by OneMoreCast 2015-01-29 03:41:09)
- OneMoreCast
- Member
- Offline
Re: SOLVED-Print layers look like Ramen noodles
cpsmicahel wrote:
OneMoreCast
Bumped flowrate up, and feedrate down...woohoocan you screen shot what you changed so i can make sure i am in the right place i have that problem too
My major problem was I switched to a RUMBA board w 1/32 stepping and my steps per mm where off. Also extruder was calibrated wrong, pretty much everything out of wack. Once all that was dialed in flow and feed stay at 100...as mentioned before its not a solution. When its properly setup both at 100 will work fine. Post pic of your EEPROM numbers from RH
"All your base are belong to us." SD4 with a RUMBA, supernight PS, 40mm fan on X motor, lawsey carriages with new better tolerance rods, flanged rear bearings, new NEMA 17 with leadscrew on Z-Axis, and e3d v6 with MK5.
Ward and Jago are my heroes
Ward and Jago are my heroes
Re: SOLVED-Print layers look like Ramen noodles
That's suck for me I was Hopping it wAz just a setting so I could get mine dialed in right
• Solidoodle Workbench Apprentice
• Creates plastic parts up to 6" x 6" x 8"
• Heated Aluminum Build Platform with Glass Bed
• Dual extruder
• Creates plastic parts up to 6" x 6" x 8"
• Heated Aluminum Build Platform with Glass Bed
• Dual extruder
34 2015-01-29 07:56:49 (edited by OneMoreCast 2015-01-29 07:57:44)
- OneMoreCast
- Member
- Offline
Re: SOLVED-Print layers look like Ramen noodles
Upload your slic3r config file..also have you tried slicing with Cura and printing!?
"All your base are belong to us." SD4 with a RUMBA, supernight PS, 40mm fan on X motor, lawsey carriages with new better tolerance rods, flanged rear bearings, new NEMA 17 with leadscrew on Z-Axis, and e3d v6 with MK5.
Ward and Jago are my heroes
Ward and Jago are my heroes
Re: SOLVED-Print layers look like Ramen noodles
Cura works but i can not set it to make # 2 Extrude as primer if i want to switch colors
• Solidoodle Workbench Apprentice
• Creates plastic parts up to 6" x 6" x 8"
• Heated Aluminum Build Platform with Glass Bed
• Dual extruder
• Creates plastic parts up to 6" x 6" x 8"
• Heated Aluminum Build Platform with Glass Bed
• Dual extruder