<![CDATA[SoliForum - 3D Printing Community — SOLVED-Print layers look like Ramen noodles]]> https://www.soliforum.com/topic/9400/solvedprint-layers-look-like-ramen-noodles/ Fri, 30 Jan 2015 03:02:35 +0000 PunBB <![CDATA[Re: SOLVED-Print layers look like Ramen noodles]]> https://www.soliforum.com/post/82322/#p82322 Cura works but i can not set it to make # 2 Extrude as primer if i want to switch colors

]]> Fri, 30 Jan 2015 03:02:35 +0000 https://www.soliforum.com/post/82322/#p82322 <![CDATA[Re: SOLVED-Print layers look like Ramen noodles]]> https://www.soliforum.com/post/82203/#p82203 Upload your slic3r config file..also have you tried slicing with Cura and printing!?

]]> Thu, 29 Jan 2015 07:56:49 +0000 https://www.soliforum.com/post/82203/#p82203 <![CDATA[Re: SOLVED-Print layers look like Ramen noodles]]> https://www.soliforum.com/post/82178/#p82178 That's suck for me I was Hopping it wAz just a setting so I could get mine dialed in right

]]> Thu, 29 Jan 2015 04:35:50 +0000 https://www.soliforum.com/post/82178/#p82178 <![CDATA[Re: SOLVED-Print layers look like Ramen noodles]]> https://www.soliforum.com/post/82171/#p82171 cpsmicahel wrote:

OneMoreCast
Bumped flowrate up, and feedrate down...woohoo


can you screen shot what you changed so i can make sure i am in the right place i have that problem too


My major problem was I switched to a RUMBA board w 1/32 stepping and my steps per mm where off. Also extruder was calibrated wrong, pretty much everything out of wack. Once all that was dialed in flow and feed stay at 100...as mentioned before its not a solution. When its properly setup both at 100 will work fine. Post pic of your EEPROM numbers from RH

]]> Thu, 29 Jan 2015 03:40:02 +0000 https://www.soliforum.com/post/82171/#p82171 <![CDATA[Re: SOLVED-Print layers look like Ramen noodles]]> https://www.soliforum.com/post/82144/#p82144 OneMoreCast
Bumped flowrate up, and feedrate down...woohoo


can you screen shot what you changed so i can make sure i am in the right place i have that problem too

]]> Thu, 29 Jan 2015 02:32:39 +0000 https://www.soliforum.com/post/82144/#p82144 <![CDATA[Re: SOLVED-Print layers look like Ramen noodles]]> https://www.soliforum.com/post/81067/#p81067 redbarret wrote:

Good logic.
But I think your putting a bandaid on your extrusion issue with that, not fixing it.


Whats the fix!? I thought tinkering settings was

]]> Fri, 23 Jan 2015 08:43:50 +0000 https://www.soliforum.com/post/81067/#p81067 <![CDATA[Re: SOLVED-Print layers look like Ramen noodles]]> https://www.soliforum.com/post/81062/#p81062 Good logic.
But I think your putting a bandaid on your extrusion issue with that, not fixing it.

]]> Fri, 23 Jan 2015 08:27:18 +0000 https://www.soliforum.com/post/81062/#p81062 <![CDATA[Re: SOLVED-Print layers look like Ramen noodles]]> https://www.soliforum.com/post/81060/#p81060 No red, i had too many problems at one time, i wanted to get the excess height and unevenness out of it (take away mk2 for now) to troubleshoot. Wanted as few variables as possible, to eliminate either something I did ie adding MK2 or software or stock part wise.

]]> Fri, 23 Jan 2015 08:00:26 +0000 https://www.soliforum.com/post/81060/#p81060 <![CDATA[Re: SOLVED-Print layers look like Ramen noodles]]> https://www.soliforum.com/post/81059/#p81059 http://s2.postimg.org/47bu20vvp/image.jpg Bumped flowrate up, and feedrate down...woohoo

]]> Fri, 23 Jan 2015 07:59:34 +0000 https://www.soliforum.com/post/81059/#p81059 <![CDATA[Re: SOLVED-Print layers look like Ramen noodles]]> https://www.soliforum.com/post/81055/#p81055 I just noticed, where did your mk2 heatbed go?
I hope you're not mistaking MK5 extruder for an MK2 heatbed and thinking of upgrading because of that.

]]> Fri, 23 Jan 2015 07:44:15 +0000 https://www.soliforum.com/post/81055/#p81055 <![CDATA[Re: SOLVED-Print layers look like Ramen noodles]]> https://www.soliforum.com/post/80958/#p80958 Well I cleaned nozzle, its deffinstly extruding thicker now and when manually pushed it goes through easier, hopefully that helps at least the horrible stripping problem. But the e3d will be on as soon as Mk5 gets here and I bought every nozzle size they had. Maybe some problems will go away once stock hotend is gone. Thanks a ton for all help and suggestions, as usual you guys are a big help to my naivness tongue

]]> Thu, 22 Jan 2015 20:00:45 +0000 https://www.soliforum.com/post/80958/#p80958 <![CDATA[Re: SOLVED-Print layers look like Ramen noodles]]> https://www.soliforum.com/post/80910/#p80910 You can use 0 if you like. It does automatic calculation in that case. I prefer to do the math myself and choose based on my needs for that particular print. Choosing the right widths can have a big impact on the look of the part and how long it takes to print.

Everyone should find what they like. BUT, when calculating the extrusion multiplier, use a constant width for your external perimeters so you know for certain what thickness you're looking for.

]]> Thu, 22 Jan 2015 13:11:26 +0000 https://www.soliforum.com/post/80910/#p80910 <![CDATA[Re: SOLVED-Print layers look like Ramen noodles]]> https://www.soliforum.com/post/80891/#p80891 IronMan wrote:

Jagowilson is referring to the Extrusion Width settings (not Nozzle Diameter) which need to be at .48 for a .4 nozzle...and theoretically you can nail your calibration box wall thickness to .48 with just diameter and steps/mm, but most times tweaks are necessary.

That's weird, mines are set to default (0) and have no problems. Maybe Slic3r automatically assumes it to be 0.48 because it knows the nozzle diameter? Would make sense.

This might also help OP.

]]> Thu, 22 Jan 2015 07:30:32 +0000 https://www.soliforum.com/post/80891/#p80891 <![CDATA[Re: SOLVED-Print layers look like Ramen noodles]]> https://www.soliforum.com/post/80815/#p80815 Also my infill wont touch perimeters...im trying to get fully solid models, i set 100% in slic3r for all under advanced and it claims extrusion width is too large, in that menu i have it set at 0 for
Default switched to.42 like it is in other settings snd still get errors


Edit; even when i change solid infill and infill to 100% it comes up w the extrusion width too high, not even touching that setting, so confused

]]> Wed, 21 Jan 2015 23:24:06 +0000 https://www.soliforum.com/post/80815/#p80815 <![CDATA[Re: SOLVED-Print layers look like Ramen noodles]]> https://www.soliforum.com/post/80808/#p80808 I have all 3 sets if pins jumped out on board...in arduino the settings sre all x2 extruder was 88x2

]]> Wed, 21 Jan 2015 22:59:49 +0000 https://www.soliforum.com/post/80808/#p80808