1 Topic by aaronboo

  • aaronboo
  • Member
  • Offline
  • Registered: 2012-11-23
  • Posts: 34

Topic: Infill issues

Hi,

Can anyone explain why the infill doesn't touch the wall? I have checked the G.Code and it looks  ok. Calibration for the Extruder and XY have already been done, belt have been tensioned.

Post's attachments

F.gcode 210.87 kb, 1 downloads since 2013-12-17 

IMG_20131217_141926.jpg
IMG_20131217_141926.jpg 2.74 mb, file has never been downloaded. 

You don't have the permssions to download the attachments of this post.

2 Reply by muddtt

  • muddtt
  • Member
  • Offline
  • From: Solidoodle 2
  • Registered: 2013-09-26
  • Posts: 276

Re: Infill issues

One possibility is the spool is hard to unravel so it causes extra tension. Make sure the roll is as easy to unwind as possible

3 Reply by aaronboo

  • aaronboo
  • Member
  • Offline
  • Registered: 2012-11-23
  • Posts: 34

Re: Infill issues

N
ope. tried that, still having the same issue. Any idea is it because of the Sli3r? Seems like my SD 2 has no issues but using SD3 i face this.

4 Reply by DePartedPrinter

  • DePartedPrinter
  • Moderator
  • Offline
  • From: Colorado
  • Registered: 2012-08-14
  • Posts: 1,478

Re: Infill issues

Looks like backlash to me.  Search.  There are fixes.

SD2 with E3D, SD Press, Form 1+
Filastruder
NYLON (taulman): http://www.soliforum.com/topic/466/nylon/

5 Reply by wardjr

  • wardjr
  • wardjr
  • Moderator
  • Offline
  • From: Minnesota
  • Registered: 2013-06-10
  • Posts: 5,624

Re: Infill issues

I would guess one of two things could be causing this.
1. Check the belt that runs from the Y drive motor to the cross shaft and make sure that is tight.
2. Check and make sure that your extruder doesn't have any wobble in it.  If it does snug up the blocks on the back rod just not to tight as you don't want them to bind.

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

wardjr's Website

6 Reply by aaronboo

  • aaronboo
  • Member
  • Offline
  • Registered: 2012-11-23
  • Posts: 34

Re: Infill issues

Thanks!

the issue has been solved smile What I did,

1) Re-Tighten the Y Axis Motor
2) Re Calibrate the Steps for the XY Stepper

7 Reply by wardjr

  • wardjr
  • wardjr
  • Moderator
  • Offline
  • From: Minnesota
  • Registered: 2013-06-10
  • Posts: 5,624

Re: Infill issues

aaronboo wrote:

Thanks!

the issue has been solved smile What I did,

1) Re-Tighten the Y Axis Motor
2) Re Calibrate the Steps for the XY Stepper

Glad to hear you got it fixed

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

wardjr's Website