Topic: Slic3r 1.0.0RC1 is out
Surprised nobody has posted already, but it's out (as of Nov 19?) and supposed to fix support settings (haven't tried yet).
- mcbride19
- Member
- Offline
Re: Slic3r 1.0.0RC1 is out
in the french section it has been posted 
Re: Slic3r 1.0.0RC1 is out
I can't seem to get Repetier 0.85 to work with this by pointing at it. Are there any software solutions with 1.0 built-in?
-SD3, E3Dv5, boz's E3D extruder, ABS from Sainsmart, mirror bed + dried hairspray + ABS slurry
-KevlarGorilla's 8x bearing threadless ball screw, 2n2r5's spring'd bed stabilizer
-fts_ltx's x-carriage, lawsy's v5 y-axis carriages, 2n2r5's beltless drive
-Overhead filament holder on 8mm rod, custom fillament feed, paeltz's simple enclosure, mini heater (opt)
-KevlarGorilla's 8x bearing threadless ball screw, 2n2r5's spring'd bed stabilizer
-fts_ltx's x-carriage, lawsy's v5 y-axis carriages, 2n2r5's beltless drive
-Overhead filament holder on 8mm rod, custom fillament feed, paeltz's simple enclosure, mini heater (opt)
- ysb
- Member
- Offline
Re: Slic3r 1.0.0RC1 is out
strange... i do it each time and had no problem even with the last version ( i use the x64 version)..
Re: Slic3r 1.0.0RC1 is out
Adrian wrote a good write up for compiling it. ^_^. Has been posted
- 2n2r5
- Member
- Offline
Re: Slic3r 1.0.0RC1 is out
Tomek wrote:
Adrian wrote a good write up for compiling it. ^_^. Has been posted
The release is out and can be downloaded. No need to compile the dev version anymore.
SD3 w/ mods:
Glass bed with QU-BD heat pad upgrade, threadless ballscrew w/ 8mm smooth rod, spectra line belt replacement, lawsy MK5 extruder, Lawsy replacement carriage, E3D hotend, Ramps 1.4 w/ reprap discount controller, DRV8825 drivers, 12v 30A PS, Acrylic case, Overkill Y-idlers, Filament alarm, Extruder fan + more.
Glass bed with QU-BD heat pad upgrade, threadless ballscrew w/ 8mm smooth rod, spectra line belt replacement, lawsy MK5 extruder, Lawsy replacement carriage, E3D hotend, Ramps 1.4 w/ reprap discount controller, DRV8825 drivers, 12v 30A PS, Acrylic case, Overkill Y-idlers, Filament alarm, Extruder fan + more.
Re: Slic3r 1.0.0RC1 is out
2n2r5 wrote:
Tomek wrote:Adrian wrote a good write up for compiling it. ^_^. Has been posted
The release is out and can be downloaded. No need to compile the dev version anymore.
Although RC1 has bugs that are fixed in dev version... so its actually better to still use dev version as RC2 is a little ways off...
And then the dev version will have fixed bugs in RC2. ..
So still worth maintaining the Dev builds... but horses for courses
Re: Slic3r 1.0.0RC1 is out
I am using it. One odd thing I noticed is that on the manual tab it used to show the print progress.Now i don't see. It
does show a blue line on the right edge of the platform and another line perpendicular to it.
SD3, E3D hotend,linear bearing on x/y axis',pillow block bearing on y conneting rod, ball bearngs on front y axis, fan on y stepper motor.
Re: Slic3r 1.0.0RC1 is out
There is a bug in the opengl libs in 1.0RC1... workaround is using a different .Dll on building. If you don't build dev builds, then it should be fixed again in RC2.
Effects win7/8 64 bit specifically, but has been seen elsewhere. .
Re: Slic3r 1.0.0RC1 is out
Umm it seems not to be a function of sli3r1.0.0RC1, I went back to .9.9 and same issue as before. I just didn't notice it after I updated the firmware til now. Could that be it? Anybody else have this issue?
SD3, E3D hotend,linear bearing on x/y axis',pillow block bearing on y conneting rod, ball bearngs on front y axis, fan on y stepper motor.
Re: Slic3r 1.0.0RC1 is out
https://github.com/alexrj/Slic3r/issues/1540 was what I was referencing.
Re: Slic3r 1.0.0RC1 is out
I got it working.
I couldn't get it to work by unpacking it in its own directory, and pointing Repetier to it with the "Setup" link.
What I did instead was backup the copy of Slic3r in the Repetier folder, then unzip directly there. Works good, but I'm getting some missing support material under solid geometry.
-SD3, E3Dv5, boz's E3D extruder, ABS from Sainsmart, mirror bed + dried hairspray + ABS slurry
-KevlarGorilla's 8x bearing threadless ball screw, 2n2r5's spring'd bed stabilizer
-fts_ltx's x-carriage, lawsy's v5 y-axis carriages, 2n2r5's beltless drive
-Overhead filament holder on 8mm rod, custom fillament feed, paeltz's simple enclosure, mini heater (opt)
-KevlarGorilla's 8x bearing threadless ball screw, 2n2r5's spring'd bed stabilizer
-fts_ltx's x-carriage, lawsy's v5 y-axis carriages, 2n2r5's beltless drive
-Overhead filament holder on 8mm rod, custom fillament feed, paeltz's simple enclosure, mini heater (opt)