<![CDATA[SoliForum - 3D Printing Community — Slic3r 1.0.0RC1 is out]]> https://www.soliforum.com/topic/4661/slic3r-100rc1-is-out/ Sat, 14 Dec 2013 03:10:32 +0000 PunBB <![CDATA[Re: Slic3r 1.0.0RC1 is out]]> https://www.soliforum.com/post/44295/#p44295 I got it working.

I couldn't get it to work by unpacking it in its own directory, and pointing Repetier to it with the "Setup" link.

What I did instead was backup the copy of Slic3r in the Repetier folder, then unzip directly there. Works good, but I'm getting some missing support material under solid geometry.

]]> Sat, 14 Dec 2013 03:10:32 +0000 https://www.soliforum.com/post/44295/#p44295 <![CDATA[Re: Slic3r 1.0.0RC1 is out]]> https://www.soliforum.com/post/44082/#p44082 https://github.com/alexrj/Slic3r/issues/1540 was what I was referencing.

]]> Thu, 12 Dec 2013 07:59:39 +0000 https://www.soliforum.com/post/44082/#p44082 <![CDATA[Re: Slic3r 1.0.0RC1 is out]]> https://www.soliforum.com/post/44075/#p44075 Umm  it seems not to be a function of sli3r1.0.0RC1,  I went  back to .9.9 and same issue as before. I just didn't notice it after I updated the firmware  til now. Could that be it? Anybody else have this issue?

]]> Thu, 12 Dec 2013 05:56:28 +0000 https://www.soliforum.com/post/44075/#p44075 <![CDATA[Re: Slic3r 1.0.0RC1 is out]]> https://www.soliforum.com/post/44070/#p44070 There is a bug in the opengl libs in 1.0RC1... workaround is using a different .Dll on building. If you don't build dev builds, then it should be fixed again in RC2.

Effects win7/8 64 bit specifically, but has been seen elsewhere. .

]]> Thu, 12 Dec 2013 05:16:23 +0000 https://www.soliforum.com/post/44070/#p44070 <![CDATA[Re: Slic3r 1.0.0RC1 is out]]> https://www.soliforum.com/post/44069/#p44069 I am using it. One odd thing I noticed is that on the manual tab it used to show the print progress.Now i don't see. It
does show a blue line on the right edge of the platform and another line perpendicular to it.

]]> Thu, 12 Dec 2013 05:03:36 +0000 https://www.soliforum.com/post/44069/#p44069 <![CDATA[Re: Slic3r 1.0.0RC1 is out]]> https://www.soliforum.com/post/43773/#p43773 2n2r5 wrote:
Tomek wrote:

Adrian wrote a good write up for compiling it. ^_^. Has been posted


The release is out and can be downloaded. No need to compile the dev version anymore.

Although RC1 has bugs that are fixed in dev version... so its actually better to still use dev version as RC2 is a little ways off...

And then the dev version will have fixed bugs in RC2. ..

So still worth maintaining the Dev builds... but horses for courses

]]> Tue, 10 Dec 2013 02:05:18 +0000 https://www.soliforum.com/post/43773/#p43773 <![CDATA[Re: Slic3r 1.0.0RC1 is out]]> https://www.soliforum.com/post/43742/#p43742 Tomek wrote:

Adrian wrote a good write up for compiling it. ^_^. Has been posted


The release is out and can be downloaded. No need to compile the dev version anymore.

]]> Mon, 09 Dec 2013 22:16:54 +0000 https://www.soliforum.com/post/43742/#p43742 <![CDATA[Re: Slic3r 1.0.0RC1 is out]]> https://www.soliforum.com/post/43741/#p43741 Adrian wrote a good write up for compiling it. ^_^. Has been posted

]]> Mon, 09 Dec 2013 22:14:51 +0000 https://www.soliforum.com/post/43741/#p43741 <![CDATA[Re: Slic3r 1.0.0RC1 is out]]> https://www.soliforum.com/post/43692/#p43692 strange... i do it each time and had no problem even with the last version ( i use the x64 version)..

]]> Mon, 09 Dec 2013 17:34:43 +0000 https://www.soliforum.com/post/43692/#p43692 <![CDATA[Re: Slic3r 1.0.0RC1 is out]]> https://www.soliforum.com/post/43679/#p43679 I can't seem to get Repetier 0.85 to work with this by pointing at it. Are there any software solutions with 1.0 built-in?

]]> Mon, 09 Dec 2013 16:16:52 +0000 https://www.soliforum.com/post/43679/#p43679 <![CDATA[Re: Slic3r 1.0.0RC1 is out]]> https://www.soliforum.com/post/42526/#p42526 in the french section it has been posted wink

]]> Mon, 25 Nov 2013 16:31:09 +0000 https://www.soliforum.com/post/42526/#p42526 <![CDATA[Slic3r 1.0.0RC1 is out]]> https://www.soliforum.com/post/42517/#p42517 Surprised nobody has posted already, but it's out (as of Nov 19?) and supposed to fix support settings (haven't tried yet).

]]> Mon, 25 Nov 2013 15:43:29 +0000 https://www.soliforum.com/post/42517/#p42517