- 28 replies
- 19,967 views
- Last post 2013-09-01 22:39:46 by Heartlander
692 Idle auto-extrusion code
by BFresh
- 2 replies
- 1,430 views
- Last post 2013-09-01 22:35:35 by Heartlander
693 DRV8825 Help please!
by Shotline
- 2 replies
- 1,982 views
- Last post 2013-08-31 23:38:33 by Shotline
694 front bed stabilization?
by chuddly
- 8 replies
- 4,702 views
- Last post 2013-08-31 22:57:36 by agentsmith
- 25 replies
- 30,592 views
- Last post 2013-08-31 07:12:20 by FatalDischarge
- 95 replies
- 87,359 views
- Last post 2013-08-31 02:19:16 by Hunter Green
- 25 replies
- 24,905 views
- Last post 2013-08-30 01:10:07 by 2n2r5
698 Time to Upgrade...
by MolecularConcept
- 4 replies
- 2,280 views
- Last post 2013-08-28 23:07:09 by MolecularConcept
699 Pololu DRV8825 drivers
by agentsmith
- 5 replies
- 5,408 views
- Last post 2013-08-25 14:29:28 by spapadim
700 Okay hackers, make this work on SD
by cmetzel
- 5 replies
- 2,473 views
- Last post 2013-08-24 16:07:27 by Hazer
701 E3D mk5 hotend - firmware changes?
by aonomus
- 1 reply
- 1,357 views
- Last post 2013-08-21 20:16:40 by DePartedPrinter
702 PCB Mk2a Heatbed Upgrade Advice?
by aonomus
- 6 replies
- 5,166 views
- Last post 2013-08-21 20:03:06 by aonomus
703 Front bed support - stops aluminum bed wobble.
by rickq
- 10 replies
- 9,226 views
- Last post 2013-08-20 19:06:01 by Tomek
- 35 replies
- 20,173 views
- Last post 2013-08-19 09:21:31 by johnforeman
705 Non compression Bowden type extruder sorta..
by rebelj12a
- 2 replies
- 2,469 views
- Last post 2013-08-18 01:59:45 by coleke
706 Thingiverse - Solidoodle 3 Filament Feed Guide
by Gomisan
- 4 replies
- 2,861 views
- Last post 2013-08-17 13:51:59 by Hunter Green
707 Anyone making a "Heat Box" to store filament?
by Stevos758
- 7 replies
- 3,981 views
- Last post 2013-08-17 09:10:49 by Shameless
708 Is this a better extruder tensioner screw?
by Heartlander
- 0 replies
- 1,399 views
- Last post 2013-08-15 20:26:58 by Heartlander
709 Glass with kapton tape
by techbuilder2175
- 15 replies
- 10,051 views
- Last post 2013-08-15 17:21:27 by Tomek
710 list of top mods?
by chuddly
- 13 replies
- 9,355 views
- Last post 2013-08-15 13:46:12 by cmetzel
711 a little help for a new guy
by chuddly
- 19 replies
- 10,430 views
- Last post 2013-08-14 21:43:57 by 2n2r5
712 A definitive way to stop the ooze!
by pastprimitive
- 12 replies
- 9,270 views
- Last post 2013-08-14 18:46:15 by pastprimitive
713 Extended filament guide
by lawsy
- 8 replies
- 4,617 views
- Last post 2013-08-11 06:20:26 by Gomisan
714 Y axis idler replacement
by Shotline
- 4 replies
- 2,822 views
- Last post 2013-08-10 15:45:31 by MolecularConcept
- 7 replies
- 18,552 views
- Last post 2013-08-09 08:51:32 by agentsmith
716 Check out my cool case!
by pastprimitive
- 9 replies
- 5,255 views
- Last post 2013-08-09 07:58:06 by G-unit
717 Replacement For Mainboard
by Sooks569
- 8 replies
- 3,905 views
- Last post 2013-08-08 03:43:06 by IanJohnson
718 Clipping oozing filament before print starts...
by pastprimitive
- 6 replies
- 4,181 views
- Last post 2013-08-08 00:53:28 by pastprimitive
719 My S3 case
by ThatGuy
- 4 replies
- 2,287 views
- Last post 2013-08-07 15:20:27 by Downeasta
720 Glass Beds, Sand them or no, Heat or not?
by JustSomeGuyTN
- 6 replies
- 6,484 views
- Last post 2013-08-05 16:50:09 by RavensCrest