1 Topic by mishu_28nmv

  • mishu_28nmv
  • Member
  • Offline
  • Registered: 2018-12-11
  • Posts: 14

Topic: Da Vinci Jr. 1.0 Pro with Cura and or Simplify3D

I have the Da Vinci Jr. 1.0 Pro printer and I'm totally satisfied with it. I am trying now to print using Cura or Simplify3D (cracked) slicers, but I have no profiles for this machine. Can someone share his profile and settings? And also I have a Rpi 3B+ with Octoprint on it, but it can not detect the printer. Software: XYZware Pro and 1.0.9 firmware. What baudrate should I use? Or what should I do?

2 Reply by carl_m1968 (edited by carl_m1968 2018-12-12 16:12:02)

  • carl_m1968
  • carl_m1968
  • Member
  • Offline
  • From: Far North almost not Dallas
  • Registered: 2014-10-17
  • Posts: 6,512

Re: Da Vinci Jr. 1.0 Pro with Cura and or Simplify3D

mishu_28nmv wrote:

I have the Da Vinci Jr. 1.0 Pro printer and I'm totally satisfied with it. I am trying now to print using Cura or Simplify3D (cracked) slicers, but I have no profiles for this machine. Can someone share his profile and settings? And also I have a Rpi 3B+ with Octoprint on it, but it can not detect the printer. Software: XYZware Pro and 1.0.9 firmware. What baudrate should I use? Or what should I do?


The Octprint will not work on the Da Vinci as it does not use a standard USB protocol.

As for the profile you would be better off setting everything based on your machine.

Another profile will get you in the ballpark but each machine is unique and it might be better to start of fresh then trying to tweak another profile to work for you.

Printing since 2009 and still love it!
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.

3 Reply by david.tucker

  • david.tucker
  • Member
  • Offline
  • Registered: 2017-10-07
  • Posts: 237

Re: Da Vinci Jr. 1.0 Pro with Cura and or Simplify3D

You can't use octoprint with XYZ printers because they communicate using a different protocol than octoprint supports.  You can pick up a wifi dongle from XYZ however I have not heard if it works well or not.

I have used Cura on my miniMaker and the defaults seem to work well, that is pick a new generic printer with your printers dimensions.  The only changes I made were to add the nozzle wipe back in at startup, and to set the fillament back to 1.7 mm rather than the default of 3.0mm.  On top of that I found that I had to raise my z-offset up to get the first layer height correct.

http://www.soliforum.com/topic/17028/pr … minimaker/

4 Reply by yizhou.he

  • yizhou.he
  • yizhou.he
  • Member
  • Offline
  • From: Boston, MA
  • Registered: 2017-07-05
  • Posts: 1,322

Re: Da Vinci Jr. 1.0 Pro with Cura and or Simplify3D

http://www.soliforum.com/topic/16702/we … r-windows/

(Da Vinci 1.0, Jr. 1.0 RAMPS, miniMaker) X4, (Creality CR-10S, CR-10 mini, Ender-3) X4, Anycubic MEGA X4, Anycubic Chrion X1, ADMILAB Gantry X2 (MonoPrice Maker Select V2, Plus, Ultimate)X4--Select mini X1, Anycubic photon X4, Wanhao duplicate D7 X1.
iNSTONE Inventor Pro X2, CTC Dual X2, ANET-A8, Hictop 3DP-11, Solidoodle Press, FLSUN I3 2017X1