1,801 New 1.1.34.4 XYZware
by mitchlandry
- 9 replies
- 4,929 views
- Last post 2015-01-09 13:52:59 by mitchlandry
- 26 replies
- 10,258 views
- Last post 2015-01-09 03:26:53 by hansen644
1,803 Cheap Filament
by scotthay
- 1 reply
- 1,286 views
- Last post 2015-01-09 00:41:21 by scotthay
1,804 Problems with calibrating
by raspears1991
- 1 reply
- 1,281 views
- Last post 2015-01-08 22:36:50 by carl_m1968
1,805 Printer doesn't know where the extruder is on the X axis
by richlechler
- 0 replies
- 898 views
- Last post 2015-01-08 20:18:36 by richlechler
1,806 S3D & Repetier: embed object
by montressor
- 0 replies
- 833 views
- Last post 2015-01-08 19:32:55 by montressor
1,807 Fine Tuning for Newbies
by jen.r.magas
- 11 replies
- 8,984 views
- Last post 2015-01-08 18:33:57 by licensed2hench
1,808 DaVinci 1.0 Extruderotomy
by cozmicray
- 2 replies
- 2,066 views
- Last post 2015-01-08 17:16:54 by cozmicray
1,809 Slic3r Settings Help
by Salmonson63
- 4 replies
- 2,291 views
- Last post 2015-01-08 17:12:17 by licensed2hench
1,810 Circles not round on one of the Davinci's 1.0
by kszwab
- 6 replies
- 29,728 views
- Last post 2015-01-08 16:51:24 by DrunkRabbit
1,811 XYZ is getting ready to release an SL based resin Printer.
by carl_m1968
- 1 reply
- 1,379 views
- Last post 2015-01-08 02:11:23 by rforeman
1,812 Esteps/mm?
by rockosmodlife
- 11 replies
- 5,928 views
- Last post 2015-01-08 01:51:32 by rockosmodlife
1,813 How warped are your glass beds?
by awesomeness
- 9 replies
- 6,640 views
- Last post 2015-01-07 20:20:33 by dsell
1,814 Reset cartridge & downgrade struggles
by kinflute
- 8 replies
- 6,343 views
- Last post 2015-01-07 18:47:16 by carl_m1968
1,815 Matter Control?
by Muledog17
- 5 replies
- 5,297 views
- Last post 2015-01-07 03:49:41 by carl_m1968
1,816 Thick bottom on prints
by parentemv
- 5 replies
- 2,588 views
- Last post 2015-01-07 03:26:35 by carl_m1968
1,817 Two printers...One computer?
by raspears1991
- 2 replies
- 1,232 views
- Last post 2015-01-06 22:03:59 by raspears1991
1,818 Updating Repetier after already flashed with repetier
by trey.mcd
- 4 replies
- 2,081 views
- Last post 2015-01-06 20:25:12 by carl_m1968
1,819 Repetier Host and Flashed Firmware Hate Me
by DrAnonymous
- 14 replies
- 9,262 views
- Last post 2015-01-06 01:05:52 by swhit321
1,820 Need help blocking with my firewall on Windows 8
by kingofallgeeks
- 1 reply
- 890 views
- Last post 2015-01-06 01:02:19 by satman49
1,821 Head won't heat - How to unload filament?
by loncaric
- 6 replies
- 4,083 views
- Last post 2015-01-05 22:11:06 by loncaric
1,822 First Layer Printing/Quality Problems
by keyblade4321
- 1 reply
- 1,767 views
- Last post 2015-01-05 01:23:51 by carl_m1968
1,823 Carrtidge Resetter
by stevendom57
- 1 reply
- 1,003 views
- Last post 2015-01-04 23:09:06 by evanalmighty
- 32 replies
- 14,500 views
- Last post 2015-01-04 19:34:49 by Neotko
1,825 Share your Slic3r install file?
by rockosmodlife
- 5 replies
- 1,674 views
- Last post 2015-01-04 17:52:23 by rockosmodlife
1,826 calibration issues!
by georgehine
- 1 reply
- 1,622 views
- Last post 2015-01-04 02:53:36 by tonyno
1,827 X/Y tilt
by Obojo
- 7 replies
- 3,753 views
- Last post 2015-01-04 02:39:19 by rockosmodlife
1,828 Delamination confirmation
by thecure
- 7 replies
- 3,975 views
- Last post 2015-01-03 23:50:11 by boxcarmib
1,829 Hacked Duo Experiences
by montressor
- 3 replies
- 2,508 views
- Last post 2015-01-03 21:22:33 by montressor
1,830 Pause mode help please
by hansen644
- 8 replies
- 5,109 views
- Last post 2015-01-03 19:06:44 by hansen644