1,771 DaVinci 1.0 job receiving problem
by rth1998
- 1 reply
- 1,187 views
- Last post 2015-01-15 23:59:28 by carl_m1968
1,772 What board is it?
by cozmicray
- 4 replies
- 2,246 views
- Last post 2015-01-15 23:54:52 by carl_m1968
1,773 New white filament from XYZ will not print.
by sdanders
- 18 replies
- 7,450 views
- Last post 2015-01-15 23:45:30 by rv.mike
1,774 Really watertight (as in holds water)
by montressor
- 5 replies
- 3,172 views
- Last post 2015-01-15 18:23:11 by madmarkus
1,775 Alternative to Glue Stick
by carl_m1968
- 24 replies
- 21,842 views
- Last post 2015-01-15 03:46:45 by darcwarrior
1,776 Second broken heat bed
by wellsje
- 3 replies
- 1,812 views
- Last post 2015-01-14 20:16:00 by wellsje
1,777 Printed blob
by rcskpeters
- 5 replies
- 2,775 views
- Last post 2015-01-14 13:24:31 by rcskpeters
1,778 Vertical Cylinders
by montressor
- 12 replies
- 5,426 views
- Last post 2015-01-14 08:49:58 by carl_m1968
- 0 replies
- 615 views
- Last post 2015-01-14 08:36:35 by Neotko
1,780 New Da Vinci cartridge showing stats from an older cartridge
by KevinME
- 6 replies
- 3,147 views
- Last post 2015-01-14 04:54:22 by carl_m1968
1,781 3D Printing Newbie Advice
by Jozer99
- 1 reply
- 866 views
- Last post 2015-01-14 02:23:30 by carl_m1968
1,782 stops mid print still?
by hansen644
- 4 replies
- 2,359 views
- Last post 2015-01-13 23:40:17 by hansen644
1,783 Flashed then flashed againn to nothing
by wgpedley
- 2 replies
- 1,230 views
- Last post 2015-01-13 20:00:19 by rockosmodlife
1,784 GCode Ref & Reusing XYZ Cartridges
by montressor
- 9 replies
- 5,489 views
- Last post 2015-01-13 14:27:22 by Wataglue
1,785 Calibration nut turns with screw
by dmcgauley
- 2 replies
- 1,197 views
- Last post 2015-01-12 23:45:26 by dmcgauley
1,786 Extruder Movement Sounded Rough
by Gee
- 0 replies
- 638 views
- Last post 2015-01-12 23:40:42 by Gee
1,787 Need 3rd party slicer software with repetier?
by awesomeness
- 5 replies
- 2,771 views
- Last post 2015-01-12 22:48:51 by montressor
1,788 Printing problems
by ekunzendorf
- 3 replies
- 3,030 views
- Last post 2015-01-12 18:14:29 by carl_m1968
1,789 Glob of filament gattering on tip, first layer?
by hansen644
- 3 replies
- 6,484 views
- Last post 2015-01-12 07:11:01 by jeff jenkins
1,790 Ok I am confused or stupid or both
by smitty9306
- 0 replies
- 747 views
- Last post 2015-01-12 05:32:39 by smitty9306
1,791 Calibration help on 3rd party filament
by swhit321
- 5 replies
- 3,153 views
- Last post 2015-01-12 01:53:50 by montressor
1,792 on/off switch on bed heater possible to prevent warping?
by hansen644
- 9 replies
- 4,057 views
- Last post 2015-01-12 00:18:01 by dubbsd
1,793 Extruder Cooling Down when it gets to the back of the bed Davinci 1.0A
by Wataglue
- 4 replies
- 1,983 views
- Last post 2015-01-11 05:34:23 by Wataglue
1,794 quality help.
by georgehine
- 13 replies
- 4,668 views
- Last post 2015-01-10 23:44:59 by georgehine
1,795 Troubleshoot print quality?
by wgenik
- 4 replies
- 2,060 views
- Last post 2015-01-10 19:09:25 by boxcarmib
1,796 sticking to bed help
by hansen644
- 6 replies
- 2,449 views
- Last post 2015-01-10 16:32:48 by hansen644
1,797 what causes this? print not touching holes
by hansen644
- 12 replies
- 5,720 views
- Last post 2015-01-10 04:04:03 by hansen644
1,798 Total failure on gear print
by parentemv
- 9 replies
- 4,261 views
- Last post 2015-01-09 22:24:16 by parentemv
1,799 Newest DaVinci - Slicing software fails.
by mcrat
- 6 replies
- 3,328 views
- Last post 2015-01-09 20:59:55 by mcrat
1,800 Version: 1.1.34.4
by parentemv
- 3 replies
- 1,475 views
- Last post 2015-01-09 14:28:59 by astrojohn