Topic: Pan Tilt for FPV
Yeah... not much to say, really. Uses all bearings and such.
Re: Pan Tilt for FPV
very cool nice job
- ysb
- Member
- Offline
Re: Pan Tilt for FPV
haaaa my FPV plane need a little test of this pan tilt.. 
nice
- ggunners
- Member
- Offline
Re: Pan Tilt for FPV
You could gyro stabilize that mount too so it stays where you move it. -- ggunners
SD2 Expert stock, ABS fume fan,
XYZ DaVinci 1.0 stock ABS, Simplify3D
QUBD Two-Up PLA, new 3D printed X gantry, Y idler, flex z coupler, extruder mount, E3D Lite
XYZ DaVinci 1.0 stock ABS, Simplify3D
QUBD Two-Up PLA, new 3D printed X gantry, Y idler, flex z coupler, extruder mount, E3D Lite
Re: Pan Tilt for FPV
thanks!
As for gyro stabilization, its going to be hooked up to a head tracker, so technically.. well, I guess it doesn't count haha
- ggunners
- Member
- Offline
Re: Pan Tilt for FPV
An if the person with the head tracker has been consuming beverages, they may be the ones that need stabilization.
SD2 Expert stock, ABS fume fan,
XYZ DaVinci 1.0 stock ABS, Simplify3D
QUBD Two-Up PLA, new 3D printed X gantry, Y idler, flex z coupler, extruder mount, E3D Lite
XYZ DaVinci 1.0 stock ABS, Simplify3D
QUBD Two-Up PLA, new 3D printed X gantry, Y idler, flex z coupler, extruder mount, E3D Lite
7 2014-02-25 16:47:38 (edited by ggunners 2014-02-25 18:23:15)
- ggunners
- Member
- Offline
Re: Pan Tilt for FPV
What's the total weight of the mount before camera and batteries, with all servos and cables? And are the files available or are you selling this?
SD2 Expert stock, ABS fume fan,
XYZ DaVinci 1.0 stock ABS, Simplify3D
QUBD Two-Up PLA, new 3D printed X gantry, Y idler, flex z coupler, extruder mount, E3D Lite
XYZ DaVinci 1.0 stock ABS, Simplify3D
QUBD Two-Up PLA, new 3D printed X gantry, Y idler, flex z coupler, extruder mount, E3D Lite
Re: Pan Tilt for FPV
Total weight without camera/batteries comes out to about 130g. Slightly heavier then normal pantilts (my wooden kit from readymadeRC is around 100) but I'm willing to trade 30g of weight for metal gear servos, full bearings, aerodynamic casings that are way more durable and protective, and no exposed wires.
I can give you the STL files if you want, but keep in mind you need 3 different bearings and 2 servos. I ordered several packs of each type needed so if you want I can build/sell one to you. Or I can give you the parts list and STL files. Your choice.
9 2014-02-28 16:23:57 (edited by ggunners 2014-02-28 16:24:55)
- ggunners
- Member
- Offline
Re: Pan Tilt for FPV
Very cool. I think the folks here would love to see the .stl files and a BOM (parts list). That way more people that have the RC hobby along with 3D printing will benefit. Thanks for offering. -- ggunners
SD2 Expert stock, ABS fume fan,
XYZ DaVinci 1.0 stock ABS, Simplify3D
QUBD Two-Up PLA, new 3D printed X gantry, Y idler, flex z coupler, extruder mount, E3D Lite
XYZ DaVinci 1.0 stock ABS, Simplify3D
QUBD Two-Up PLA, new 3D printed X gantry, Y idler, flex z coupler, extruder mount, E3D Lite
Re: Pan Tilt for FPV
I like this! Did you have to drill out the plates and parts after printing or were you able to print all the holes?
Re: Pan Tilt for FPV
I printed all the holes slightly small on purpose so the screws tap in nicely. Others needed slight sanding.