Topic: Repitier host 0.95e
upgrading to the newest, anyone see any issues with this yet?
Overkill is underrated!!!
- SnakeEyes
- Member
- Offline
- rjp350z
- Member
- Offline
Re: Repitier host 0.95e
Running a 4 hour print on it now - no issues seen yet
- SnakeEyes
- Member
- Offline
Re: Repitier host 0.95e
you have any issues getting started? Just got it to see my temps but no printer control.
Overkill is underrated!!!
- rjp350z
- Member
- Offline
Re: Repitier host 0.95e
no problems at all. Installed with no problems. Notice the "Change settings not saving" bug is still there but been living with it for a while now
Re: Repitier host 0.95e
They fixed the bug where if you specified another slic3r config directory, you edited in the specified directory, but sliced with the default. Now I can keep my slic3r profiles synced on all my PC's.
They need to put a PIN on that 3d-toolbar, it sliding in and out is driving me bonkers..
Re: Repitier host 0.95e
It freezes for me when I try opening it. I had to go back to the previous version.
SD2 w/ mods: Rumba controller, ATX PSU, SD pro case, glass bed, with more to come...
- dubbsd
- Member
- Offline
Re: Repitier host 0.95e
it freezes on opening for me also
on a Win.7 machine.
Ultimaker S3.
- rjp350z
- Member
- Offline
Re: Repitier host 0.95e
After Running about 3 hours last night RH froze on me and ruined the print. Not sure if it was a fluke has something to do with the new version. Will start print again tonight and watch more closely...
Also, I had similar problem with previous version crashing immediately upon opening with WIN 7.
I had to ensure that the previous version was fully uninstalled before trying to install the new one.
Re: Repitier host 0.95e
For me, it has been hanging after slic3r tries to write the file:
21:15:07.772 : <Slic3r> => Exporting G-code to E:\Users\TheBogueRat\AppData\Local\RepetierHost\composition.gcode
Sometimes it will come back after a few minutes but tonight I let it sit for an hour and nothing happened. The progress bar kept scrolling. It's worse with multiple objects on the platter.
I installed and selected Slic3r 9.10 and that seemed to fix my problem but it is still slower than before.
Win 7
10 2014-01-16 02:34:51 (edited by rjp350z 2014-01-16 02:35:19)
- rjp350z
- Member
- Offline
Re: Repitier host 0.95e
Wavesurf wrote:
For me, it has been hanging after slic3r tries to write the file:
21:15:07.772 : <Slic3r> => Exporting G-code to E:\Users\TheBogueRat\AppData\Local\RepetierHost\composition.gcode
Sometimes it will come back after a few minutes but tonight I let it sit for an hour and nothing happened. The progress bar kept scrolling. It's worse with multiple objects on the platter.
I installed and selected Slic3r 9.10 and that seemed to fix my problem but it is still slower than before.
Win 7
I had similar issue and had to turn off "AVOID CROSSING PERIMITERS" as it seemed to cause slic3r to hang.
Also, had twice now RH Crash in the middle of a print and only Error I could see in WIN 7 event viewer was an unhandled exception in OPENGL
Application: RepetierHost.exe
Framework Version: v4.0.30319
Description: The process was terminated due to an unhandled exception.
Exception Info: System.AccessViolationException
Stack:
at OpenTK.Graphics.OpenGL.GL.DrawElements[[System.Int32, mscorlib, Version=4.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089]](OpenTK.Graphics.OpenGL.PrimitiveType, Int32, OpenTK.Graphics.OpenGL.DrawElementsType, Int32[])
at RepetierHost.model.GCodeVisual.drawSegment(RepetierHost.model.GCodePath)
at RepetierHost.model.GCodeVisual.Paint()
at RepetierHost.view.ThreeDControl.DrawModels()
at RepetierHost.view.ThreeDControl.gl_Paint(System.Object, System.Windows.Forms.PaintEventArgs)
at OpenTK.GLControl.OnPaint(System.Windows.Forms.PaintEventArgs)
at System.Windows.Forms.Control.PaintWithErrorHandling(System.Windows.Forms.PaintEventArgs, Int16)
at System.Windows.Forms.Control.WmPaint(System.Windows.Forms.Message ByRef)
at System.Windows.Forms.Control.WndProc(System.Windows.Forms.Message ByRef)
at System.Windows.Forms.NativeWindow.Callback(IntPtr, Int32, IntPtr, IntPtr)
at System.Windows.Forms.UnsafeNativeMethods.DispatchMessageW(MSG ByRef)
at System.Windows.Forms.Application+ComponentManager.System.Windows.Forms.UnsafeNativeMethods.IMsoComponentManager.FPushMessageLoop(IntPtr, Int32, Int32)
at System.Windows.Forms.Application+ThreadContext.RunMessageLoopInner(Int32, System.Windows.Forms.ApplicationContext)
at System.Windows.Forms.Application+ThreadContext.RunMessageLoop(Int32, System.Windows.Forms.ApplicationContext)
at RepetierHost.Program.Main(System.String[])11 2014-01-16 02:40:45 (edited by rjp350z 2014-01-16 02:41:47)
- rjp350z
- Member
- Offline
Re: Repitier host 0.95e
doppler wrote:
They fixed the bug where if you specified another slic3r config directory, you edited in the specified directory, but sliced with the default. Now I can keep my slic3r profiles synced on all my PC's.
They need to put a PIN on that 3d-toolbar, it sliding in and out is driving me bonkers..
The problem I still see with the new Slic3r is if I change say PERIMITERS FROM 3 to 4 once I hit save I watch it physically go back to 3.
However, If I change it to something stupid (like 3 to 40) it takes it when saving then I can change form 40 to 4 and it saves fine. GO FIGURE
Re: Repitier host 0.95e
Thanks, I turned off that option and it seems like it is back to normal.
I've been using a Panelolu because I had issues with computer lag. I miss the computer interface but the Panelolu is great and has eliminated host issues for me.
Re: Repitier host 0.95e
Too funny, I've seen that problem for a long time now. I tried using the little arrows to change the number; tried changing a bunch of stuff at the same time; and finally just broke down and look for the .ini file to change it manually.
You do have to change it to a huge number, save, then change back to what you wanted in the first place for it to work.
I can't complain too much, the price was great and the SD2 has been working like a champ since I got it tuned in.
- rjp350z
- Member
- Offline
Re: Repitier host 0.95e
This issue was already submitted by others also on the GITHUB
- SnakeEyes
- Member
- Offline
Re: Repitier host 0.95e
Still cant get 95e to see my printer, 85b works fine. I shouldn't have to uninstall the old version should I?
Overkill is underrated!!!
Re: Repitier host 0.95e
same, it slices fine, i just can't get it to recognize my printer or connect to my sd3, any ideas? .85 is still running fine.
- SnakeEyes
- Member
- Offline
Re: Repitier host 0.95e
tried 95 f. still will not connect to my printer. does it do anything better or am i trying to get it to work just for a better paint job?
Overkill is underrated!!!
Re: Repitier host 0.95e
I am running .95 with slic3r 1.0. I like the look and feel of .95. I did have to change some defaults to run the printer. When I get home, I will post some print screens. Slic3r 1.0 is giving me really nice prints on some small clips and pin I have been running. Much cleaner that the previous version.
Re: Repitier host 0.95e
Just updated to the latest version (0.95F). I am having trouble with this version loading models. It has been taking 30 min and only about 20% done importing the .stl file. It could be the .stl file but I was importing the files into the a previous version (0.82B) without any real delay.
Running Windows 7 with an SD3.
I have been using Skeinforge for all my prints and I have decided to upgrade repeiter and get the latest Slic3r working. I was very impressed how well it sliced models and printed them on an Orion Delta printer I was setting up.
Any thoughts on loading .stl time would be helpful!
Re: Repitier host 0.95e
How big are the stl's? you need lots of ram in windows for larger stl's.
Re: Repitier host 0.95e
I have been scaling back the .stl file size from the previous version of repeiter host. I am down to around 100k triangles with a file size of ~12MB. I have 8 GB of RAM on my machine.
Re: Repitier host 0.95e
I just ran a 20mb file in a couple seconds. You probably need to try running the model through netfabb to clean it up.
- rjp350z
- Member
- Offline
Re: Repitier host 0.95e
wbrandsmeier wrote:
Just updated to the latest version (0.95F). I am having trouble with this version loading models. It has been taking 30 min and only about 20% done importing the .stl file. It could be the .stl file but I was importing the files into the a previous version (0.82B) without any real delay.
Running Windows 7 with an SD3.
I have been using Skeinforge for all my prints and I have decided to upgrade repeiter and get the latest Slic3r working. I was very impressed how well it sliced models and printed them on an Orion Delta printer I was setting up.
Any thoughts on loading .stl time would be helpful!
Have you tried turning off "AVOID CROSSING PERIMETERS" before slicing. There is a known issue with slicing either taking too long or hanging with the feature turned on.
Re: Repitier host 0.95e
ok, so it is more than likely my model.
Thanks!
Re: Repitier host 0.95e
how did everyone quickly copy over there old settings to the new software?