1 Topic by L.woinson95

  • L.woinson95
  • Member
  • Offline
  • From: Burnley, Lancs, UK
  • Registered: 2015-02-07
  • Posts: 163

Topic: Layer issue

Right guys used the Hobbyking Esun filament to print this using the following settings:

Layer Height - 0.3
Density - 10%
Speed - Normal

But some areas seem to of 'split' I have attached the images of it to show what I mean...

Any help would be grateful thank you

Post's attachments

IMG_1522.JPG
IMG_1522.JPG 1.3 mb, file has never been downloaded. 

IMG_1523.JPG
IMG_1523.JPG 1.38 mb, file has never been downloaded. 

IMG_1524.JPG
IMG_1524.JPG 1.5 mb, 1 downloads since 2015-02-28 

You don't have the permssions to download the attachments of this post.

2 Reply by carl_m1968

  • carl_m1968
  • carl_m1968
  • Member
  • Offline
  • From: Far North almost not Dallas
  • Registered: 2014-10-17
  • Posts: 6,512

Re: Layer issue

Raise your nozzle temp by 5 to 10 degrees. That looks like a poor bond issue. Since the infill is ow and the part is small it should be more bond then uneven cooling which can also cause splitting.

Printing since 2009 and still love it!
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.

3 Reply by L.woinson95 (edited by L.woinson95 2015-02-28 21:00:31)

  • L.woinson95
  • Member
  • Offline
  • From: Burnley, Lancs, UK
  • Registered: 2015-02-07
  • Posts: 163

Re: Layer issue

That figure is 120mm tall? I printed a small one off and no issues

Will try turning the temp up and re print

4 Reply by carl_m1968

  • carl_m1968
  • carl_m1968
  • Member
  • Offline
  • From: Far North almost not Dallas
  • Registered: 2014-10-17
  • Posts: 6,512

Re: Layer issue

L.woinson95 wrote:

That figure is 120mm tall? I printed a small one off and no issues

Will try turning the temp up and re print


Sorry it looked small in the pics.. But if it is that tall that could be the issue. You need to up your temp to 235 and the bed should be 110.

Printing since 2009 and still love it!
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.

5 Reply by L.woinson95

  • L.woinson95
  • Member
  • Offline
  • From: Burnley, Lancs, UK
  • Registered: 2015-02-07
  • Posts: 163

Re: Layer issue

I turned the temp up and printed a smaller charmander out (attached) would this look like I had the temp too high for it?

I then printed a compressor off and it looks fine?

Also how do you activate supports on Slic3r?

Thanks

Post's attachments

Charmander.JPG
Charmander.JPG 1.44 mb, file has never been downloaded. 

Compressor Blade.JPG
Compressor Blade.JPG 2.08 mb, file has never been downloaded. 

You don't have the permssions to download the attachments of this post.