1 Topic by mdrVB6 (edited by mdrVB6 2015-01-05 03:29:37)

  • mdrVB6
  • Member
  • Offline
  • Registered: 2013-12-18
  • Posts: 717

Topic: Stupid question- where is the code input line in Repetier Host V1.0.6?

So I finally updated repetier and now I can't find where to enter my M code/ G code commands.  This is probably really simple but I looked all over.  Does anyone know where I can find this?  Also, where is the log?  It used to drag up from the bottom now I don't see it at all.  Thanks and don't laugh at me haha.

Picture below.  Left side is mine with no code input.  Right side is what the documentation from the repetier website shows.  Someone tell me there is any easy check box somewhere and I'm not going insane.  Thanks

PunBB bbcode test

SD4 w/ RUMBA, E3D Volcano, all bearings, glass bed

2 Reply by satman49

  • satman49
  • Member
  • Offline
  • From: virginia
  • Registered: 2012-12-28
  • Posts: 867

Re: Stupid question- where is the code input line in Repetier Host V1.0.6?

Do you mean how to slice an object?Click toggle log at top, it will appear.

SD3, E3D hotend,linear bearing on x/y axis',pillow block bearing on y conneting rod, ball bearngs on front y axis, fan on y stepper motor.

3 Reply by mdrVB6

  • mdrVB6
  • Member
  • Offline
  • Registered: 2013-12-18
  • Posts: 717

Re: Stupid question- where is the code input line in Repetier Host V1.0.6?

No, I mean how to enter manual g code commands, totally different.

SD4 w/ RUMBA, E3D Volcano, all bearings, glass bed

4 Reply by AZERATE

  • AZERATE
  • AZERATE
  • PRINTiT
  • Offline
  • From: Chicago
  • Registered: 2013-11-28
  • Posts: 2,077

Re: Stupid question- where is the code input line in Repetier Host V1.0.6?

I updated a few months ago, and it took me some time to get used to the new layout.
My log is still found at the bottom. Upon slicing, you have to click on Preview, then the second tab of gCode editor to view the sliced code. To give commands, you just type them into the Manual section and everything will pop up below.

I hope I understood what you meant. smile

Printit Mason and Printit Horizon printers
Multiple SD2s- Bulldog XL, E3D v5/v6/Lite6, Volcano, Hobb Goblin, Titan, .9 motor, Lawsy carriages, direct Y drive, fishing line...the list goes on
Filawinder and Filastruder #1870.....worth every penny!

5 Reply by pirvan

  • pirvan
  • pirvan
  • Member
  • Offline
  • From: San Francisco
  • Registered: 2013-03-27
  • Posts: 1,797

Re: Stupid question- where is the code input line in Repetier Host V1.0.6?

You're in Easy Mode.  The Easy Mode toggle mode button is just above, next to the Printer settings button

To print or, 3D print, that is the question...
SD3 printer w/too many mods,  Printrbot Simple Maker Ed.,  FormLabs Form 1+
AnyCubic Photon, Shining 3D EinScan-S & Atlas 3D scanners...
...and too much time on my hands.

6 Reply by mdrVB6

  • mdrVB6
  • Member
  • Offline
  • Registered: 2013-12-18
  • Posts: 717

Re: Stupid question- where is the code input line in Repetier Host V1.0.6?

pirvan wrote:

You're in Easy Mode.  The Easy Mode toggle mode button is just above, next to the Printer settings button


See, I told you it was a stupid question.  That was it, thanks!

SD4 w/ RUMBA, E3D Volcano, all bearings, glass bed

7 Reply by mdrVB6 (edited by mdrVB6 2015-01-15 16:17:52)

  • mdrVB6
  • Member
  • Offline
  • Registered: 2013-12-18
  • Posts: 717

Re: Stupid question- where is the code input line in Repetier Host V1.0.6?

Bumping this because I am just now getting back to fixing my mini kossel... where is the damn output log?  It is not within the G code area and I can't find it at all!  Really feeling dumb again...

In the older versions if repetier, you could just drag up a window from the bottom of the screen to see communications with your printer is real time.  Is that really gone?  Thanks.

SD4 w/ RUMBA, E3D Volcano, all bearings, glass bed

8 Reply by ThrillaInManilla

  • ThrillaInManilla
  • Newbie
  • Offline
  • Registered: 2015-04-04
  • Posts: 1

Re: Stupid question- where is the code input line in Repetier Host V1.0.6?

I'm having the same issue... I can't find the output log in Repetier to verify everything is communicating properly.

9 Reply by mdrVB6

  • mdrVB6
  • Member
  • Offline
  • Registered: 2013-12-18
  • Posts: 717

Re: Stupid question- where is the code input line in Repetier Host V1.0.6?

You have to click "toggle log" in the top panel of buttons.  You can no longer drag it up to expand the log.

SD4 w/ RUMBA, E3D Volcano, all bearings, glass bed