1 Topic by markthorpe

  • markthorpe
  • Member
  • Offline
  • Registered: 2013-11-22
  • Posts: 12

Topic: Snapped Acrylic

Hello all,

The acrylic jigsaw has snapped on my Solidoodle and now I can no longer print. I have ordered a replacement from imakr but these guys can take weeks to turn around an order.
I had printed http://www.thingiverse.com/thing:111213 as a replacement but one of the parts didn't quite come out right.
Anyone willing to run one off and send me it so that I can do some Xmas prints ?
I'll reimburse for ABS and Postage.
Cheers!
Mark

2 Reply by 2n2r5

  • 2n2r5
  • 2n2r5
  • Member
  • Offline
  • From: Frederick, MD
  • Registered: 2013-05-09
  • Posts: 1,208

Re: Snapped Acrylic

Pm me with your address. I will get one in the mail tonight or tomorrow.

SD3 w/ mods:
Glass bed with QU-BD heat pad upgrade, threadless ballscrew w/ 8mm smooth rod, spectra line belt replacement, lawsy MK5 extruder, Lawsy replacement carriage, E3D hotend, Ramps 1.4 w/ reprap discount controller, DRV8825 drivers, 12v 30A PS, Acrylic case, Overkill Y-idlers, Filament alarm, Extruder fan + more.

2n2r5's Website

3 Reply by markthorpe (edited by markthorpe 2013-12-02 13:53:15)

  • markthorpe
  • Member
  • Offline
  • Registered: 2013-11-22
  • Posts: 12

Re: Snapped Acrylic

Thanks 2n2r5. Much, much appreciated

4 Reply by 2n2r5

  • 2n2r5
  • 2n2r5
  • Member
  • Offline
  • From: Frederick, MD
  • Registered: 2013-05-09
  • Posts: 1,208

Re: Snapped Acrylic

No problem. If anyone in the UK wants to help out then it might be a bit quicker. If no one else responds I will throw one in the mail for you asap.

SD3 w/ mods:
Glass bed with QU-BD heat pad upgrade, threadless ballscrew w/ 8mm smooth rod, spectra line belt replacement, lawsy MK5 extruder, Lawsy replacement carriage, E3D hotend, Ramps 1.4 w/ reprap discount controller, DRV8825 drivers, 12v 30A PS, Acrylic case, Overkill Y-idlers, Filament alarm, Extruder fan + more.

2n2r5's Website

5 Reply by markthorpe

  • markthorpe
  • Member
  • Offline
  • Registered: 2013-11-22
  • Posts: 12

Re: Snapped Acrylic

Got them today thanks.
Will fit them now.
Much appreciated.
Mark

6 Reply by 2n2r5

  • 2n2r5
  • 2n2r5
  • Member
  • Offline
  • From: Frederick, MD
  • Registered: 2013-05-09
  • Posts: 1,208

Re: Snapped Acrylic

Nice! I had a bit of trouble with that black filament. The layer adhesion was a little questionable. It should work fine for the MK5 but make sure you print spares when you get a chance.

SD3 w/ mods:
Glass bed with QU-BD heat pad upgrade, threadless ballscrew w/ 8mm smooth rod, spectra line belt replacement, lawsy MK5 extruder, Lawsy replacement carriage, E3D hotend, Ramps 1.4 w/ reprap discount controller, DRV8825 drivers, 12v 30A PS, Acrylic case, Overkill Y-idlers, Filament alarm, Extruder fan + more.

2n2r5's Website