1 Topic by LdyMox

  • LdyMox
  • LdyMox
  • Member
  • Offline
  • From: Buffalo, NY USA
  • Registered: 2013-04-27
  • Posts: 576

Topic: Won't Start Printing

I have had my Solidoodle about a week a half and it seems it won't start printing anymore. I can control the axis, extrude just fine. Everything seems to heat up just fine. But when I run the job now nothing happens even though it is up to temperature. The bed and hotend is hot to the touch.

If I try to run the job and nothing happens after that I can not control the Solidoodle until I reset. I got it to work once in the last day by resetting my computer and keep trying. Also when I try to print it does not home like it used to when it was working.

Tammy
Solidoodle 2
E3Dv6 Hotend, MK5 v6 version, Glass Bed, Anti Z backlash slop nut, SureStepr SD8825 1/32 Extruder Driver, makeshift breakaway plexiglass case; . L-Cheapo 3.8 Watt Laser Attachment w/Custom built enclosure
From Buffalo, NY, USA

2 Reply by LdyMox

  • LdyMox
  • LdyMox
  • Member
  • Offline
  • From: Buffalo, NY USA
  • Registered: 2013-04-27
  • Posts: 576

Re: Won't Start Printing

Both in Repeiter-Host and Pronterface it thinks it is printing but does not.

Tammy
Solidoodle 2
E3Dv6 Hotend, MK5 v6 version, Glass Bed, Anti Z backlash slop nut, SureStepr SD8825 1/32 Extruder Driver, makeshift breakaway plexiglass case; . L-Cheapo 3.8 Watt Laser Attachment w/Custom built enclosure
From Buffalo, NY, USA

3 Reply by satman49

  • satman49
  • Member
  • Offline
  • From: virginia
  • Registered: 2012-12-28
  • Posts: 867

Re: Won't Start Printing

Are the led lights on?

SD3, E3D hotend,linear bearing on x/y axis',pillow block bearing on y conneting rod, ball bearngs on front y axis, fan on y stepper motor.

4 Reply by LdyMox

  • LdyMox
  • LdyMox
  • Member
  • Offline
  • From: Buffalo, NY USA
  • Registered: 2013-04-27
  • Posts: 576

Re: Won't Start Printing

Yes, that one red LED in the back. It is weird since I can do the axis, extrude. Just if I hit print nothing happens but the softwares think stuff is happening

Tammy
Solidoodle 2
E3Dv6 Hotend, MK5 v6 version, Glass Bed, Anti Z backlash slop nut, SureStepr SD8825 1/32 Extruder Driver, makeshift breakaway plexiglass case; . L-Cheapo 3.8 Watt Laser Attachment w/Custom built enclosure
From Buffalo, NY, USA

5 Reply by LdyMox

  • LdyMox
  • LdyMox
  • Member
  • Offline
  • From: Buffalo, NY USA
  • Registered: 2013-04-27
  • Posts: 576

Re: Won't Start Printing

I already tried a new port, reinstall software, even a new USB cable

Tammy
Solidoodle 2
E3Dv6 Hotend, MK5 v6 version, Glass Bed, Anti Z backlash slop nut, SureStepr SD8825 1/32 Extruder Driver, makeshift breakaway plexiglass case; . L-Cheapo 3.8 Watt Laser Attachment w/Custom built enclosure
From Buffalo, NY, USA

6 Reply by satman49

  • satman49
  • Member
  • Offline
  • From: virginia
  • Registered: 2012-12-28
  • Posts: 867

Re: Won't Start Printing

On the gcode tab,  it shows the code after slicing?

SD3, E3D hotend,linear bearing on x/y axis',pillow block bearing on y conneting rod, ball bearngs on front y axis, fan on y stepper motor.

7 Reply by Krythis

  • Krythis
  • Krythis
  • Member
  • Offline
  • From: Depew, NY
  • Registered: 2013-02-27
  • Posts: 185

Re: Won't Start Printing

Silly question, but do you have Repetier set to show errors and it is not reporting any?

E3D-v4 Hotend, MK5 carriage with round plastic wire conduit , 3/16" tempered glass,  Well nut, SureStepr SD8825 1/32 Extruder Driver, PowerEdge 2650 500W PS, QU-BD heated bed, circuit board fan, hinged plexiglass enclosure with plastic tray top. Other than that mostly stock SD3

8 Reply by LdyMox

  • LdyMox
  • LdyMox
  • Member
  • Offline
  • From: Buffalo, NY USA
  • Registered: 2013-04-27
  • Posts: 576

Re: Won't Start Printing

yes. I even switched to a simple cylinder I printed a week before

Tammy
Solidoodle 2
E3Dv6 Hotend, MK5 v6 version, Glass Bed, Anti Z backlash slop nut, SureStepr SD8825 1/32 Extruder Driver, makeshift breakaway plexiglass case; . L-Cheapo 3.8 Watt Laser Attachment w/Custom built enclosure
From Buffalo, NY, USA

9 Reply by LdyMox

  • LdyMox
  • LdyMox
  • Member
  • Offline
  • From: Buffalo, NY USA
  • Registered: 2013-04-27
  • Posts: 576

Re: Won't Start Printing

No errors but I just noticed something. For slicer I had made a "PLA" filament settings. Oddly enough the one I made(PLA) works but not the default ABS it came with which I never changed. Well at at least I have it responding again.

Tammy
Solidoodle 2
E3Dv6 Hotend, MK5 v6 version, Glass Bed, Anti Z backlash slop nut, SureStepr SD8825 1/32 Extruder Driver, makeshift breakaway plexiglass case; . L-Cheapo 3.8 Watt Laser Attachment w/Custom built enclosure
From Buffalo, NY, USA

10 Reply by LdyMox

  • LdyMox
  • LdyMox
  • Member
  • Offline
  • From: Buffalo, NY USA
  • Registered: 2013-04-27
  • Posts: 576

Re: Won't Start Printing

That ABS slicer material profile must be corrupt since making a duplicate of it from scratch seems to work. Very odd.

Tammy
Solidoodle 2
E3Dv6 Hotend, MK5 v6 version, Glass Bed, Anti Z backlash slop nut, SureStepr SD8825 1/32 Extruder Driver, makeshift breakaway plexiglass case; . L-Cheapo 3.8 Watt Laser Attachment w/Custom built enclosure
From Buffalo, NY, USA