1 Topic by AWa.

  • AWa.
  • Newbie
  • Offline
  • Registered: 2016-02-10
  • Posts: 4

Topic: da Vinci 2.0A Duo with e3d v6

Hi,

I put the e3d v6 clone into my da Vinci 2.0A Duo.
It's seems to work fine.

Photo story:
https://photos.app.goo.gl/PqT8FGYR397Uv8uC2

The parts I got from https://www.trianglelab.org/ (aliexpress).

AWa.

2 Reply by yizhou.he

  • yizhou.he
  • yizhou.he
  • Member
  • Offline
  • From: Boston, MA
  • Registered: 2017-07-05
  • Posts: 1,358

Re: da Vinci 2.0A Duo with e3d v6

wow! that's some serious cutting and drilling...

(Da Vinci 1.0, Jr. 1.0 RAMPS, miniMaker) X4, (Creality CR-10S, CR-10 mini, Ender-3) X4, Anycubic MEGA X4, Anycubic Chrion X1, ADMILAB Gantry X2 (MonoPrice Maker Select V2, Plus, Ultimate)X4--Select mini X1, Anycubic photon X4, Wanhao duplicate D7 X1.
iNSTONE Inventor Pro X2, CTC Dual X2, ANET-A8, Hictop 3DP-11, Solidoodle Press, FLSUN I3 2017X1

3 Reply by AWa.

  • AWa.
  • Newbie
  • Offline
  • Registered: 2016-02-10
  • Posts: 4

Re: da Vinci 2.0A Duo with e3d v6

A little...
But it fit perfectly and can be used with original firmware and software.
All features work except crappy XYZ levelling. 
Adding the levelling pin is possible and it will take a few minutes. But what for?
Bed levelling with feeler is the best method for this printer imo.

If you install XYZware trainer
  http://www.soliforum.com/topic/16988/xyzware-trainer/
It is possible to use different nozzle diameter with XYZware.

4 Reply by yizhou.he

  • yizhou.he
  • yizhou.he
  • Member
  • Offline
  • From: Boston, MA
  • Registered: 2017-07-05
  • Posts: 1,358

Re: da Vinci 2.0A Duo with e3d v6

Do you think it is possible to cut the fin shorter and leave the heat block untouched? That can save a lots of cutting if possible.

(Da Vinci 1.0, Jr. 1.0 RAMPS, miniMaker) X4, (Creality CR-10S, CR-10 mini, Ender-3) X4, Anycubic MEGA X4, Anycubic Chrion X1, ADMILAB Gantry X2 (MonoPrice Maker Select V2, Plus, Ultimate)X4--Select mini X1, Anycubic photon X4, Wanhao duplicate D7 X1.
iNSTONE Inventor Pro X2, CTC Dual X2, ANET-A8, Hictop 3DP-11, Solidoodle Press, FLSUN I3 2017X1

5 Reply by AWa.

  • AWa.
  • Newbie
  • Offline
  • Registered: 2016-02-10
  • Posts: 4

Re: da Vinci 2.0A Duo with e3d v6

yizhou.he wrote:

Do you think it is possible to cut the fin shorter and leave the heat block untouched? That can save a lots of cutting if possible.

Hi,

I am not sure if I understood you correctly.
I think that removing more fins from hot side of heat sink is not a good idea.

But in my solution the heater block is untouched.
I machined only  the original XYZ heat sink and the E3D V6 heat sink.

If you are looking for simpler solution you can look into "E3D DUO Hotend.pdf", maybe it will work.

Post's attachments

E3D DUO Hotend.pdf 347.25 kb, 23 downloads since 2018-06-10 

XYZ DUO hotend.pdf 376.84 kb, 18 downloads since 2018-06-10 

You don't have the permssions to download the attachments of this post.